Author Topic: Best Miter saw options?  (Read 5294 times)

0 Members and 1 Guest are viewing this topic.

Offline oneeyesquare

  • Posts: 37
Re: Best Miter saw options?
« Reply #30 on: July 23, 2017, 10:03 AM »
I was also bummed by the dust collection outlet. Somebody dropped the ball on that one big time.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Online jpmeunier

  • Posts: 11
Re: Best Miter saw options?
« Reply #31 on: July 23, 2017, 12:11 PM »
Also for those interested the height is 98mm. Sets on rubber feet so you can level it with bolt tightening.

Offline BBuild

  • Posts: 73
Re: Best Miter saw options?
« Reply #32 on: July 24, 2017, 05:34 PM »
Spotted this today:


https://www.burnstools.com/ls1019l-10-dual-slide-compound-miter-saw

Thanks for posting that. I was the first person to buy the saw from them. I really wanted to look it over in person first so it was well worth the drive.

I'll post an update after I have a solid opinion on it's performance.
Kapex w/MFT-k &  crown stops,  TS 55,  MFT-3,  MFT-800,  CT 26 w/ rrp HEPA,  CT 22 w/ LL bag,  CT Midi,  CXS,  RAS 115 w/ plug it,  RO 90,  ETS 150/5,  ETS 125,  RS 400,  EHL 65 w/ plug it,  HL 850 w/ bench unit,  OF 1010 w/LR32

Offline Oldwood

  • Posts: 264
  • Alberta, Canada
Re: Best Miter saw options?
« Reply #33 on: July 30, 2017, 11:46 AM »
Short review. Got the Makita and used all day yesterday. I'm likening it to a fully loaded truck vs the Kapex as zoomy sports.  car.
Makita cuts super smooth. Smoother than the Kapex.
I would say not as ridgid on the slide. A little drift on some big miters on 5/4 material. Not bad, just not the train track performance of the Kapex.
Laser is ok for matching miters, but no where's near the accuracy of the Kapex; however, I can see the blade of the Makita much better. Need to peruse the manual for adjustment options.
Dust collection was 80% of the Kapex. Adequate. I'm running a split hose and had tools hooked up to the other end, so on reduced suction anyway.
Did not worry one bit the motor was gonna unexpectedly grenade. That was nice.
Left it sitting on the job site with a cable through it vs. throwing it in the van. I can absorb a $540 theft loss a little bit easier than a $1600 loss; however, no local purchase options yet for the Makita.
Fixed the idiot button with some 2p-10. Grab, squeeze and cut. Like it should be. Seriously contemplating, modding the Kapex's to remove the horribly over complicated safety trigger.
The full 60 degree both ways is wonderful. I need to use that today on some 1x8 bead board at 51.5 degrees going up along a stair skirt. Should make that pretty easy.
Old Kapex will get sent in to repair head spring which no longer lifts the head. Kinda neutral at this point. That will be warranty trip #3. New Kapex is still a warranty virgin. We shall see.
If you have any questions, Ill try to answer later tonight.

Does your saw make a dragging sound when you swing the table from 90 to 45? I just pulled it out of the box and is seems to drag on the UHMW shim. Don't know if that is by design or not?

Thanks,
Gerry
Real knowledge is to know the extent of one's ignorance.
Confucius

Offline Oldwood

  • Posts: 264
  • Alberta, Canada
Re: Best Miter saw options?
« Reply #34 on: July 31, 2017, 12:38 PM »
So to answer my own question, it is by design.

A heads up for anyone in Canada looking for this saw there are two models the 1019L and the 1019 the 1019L has the laser guide the the 1019 does not. It seems in Canada no one wants to stock the 1019L

Gerry
Real knowledge is to know the extent of one's ignorance.
Confucius

Offline oneeyesquare

  • Posts: 37
Re: Best Miter saw options?
« Reply #35 on: August 02, 2017, 09:13 PM »

Does your saw make a dragging sound when you swing the table from 90 to 45? I just pulled it out of the box and is seems to drag on the UHMW shim. Don't know if that is by design or not?

Thanks,
Gerry

It makes a zipper sound. Like a tent zipper. Smooth action. Works great!

Offline online421

  • Posts: 64
Re: Best Miter saw options?
« Reply #36 on: August 02, 2017, 09:21 PM »
if you want the best of the best mitre saw and the saw stays stationary. go to Omga.

the whole thing is made of cast iron except the saw guard and the power on/off button

I had a T50350 and then upgraded to their double mitre saw.

You wont look at anything else ever again.

List price is $4000 USD for a base model.

Robland NX410Pro
Masterwood OMB1V
Omga AL129
SCM 5 RCS110
Chicago Pneumatics CPRS10500
Ceccato CDX 12
Holytek DC006
Festool DF700XL, CT36, LEX3
JLT 190BM2, 79K10
Danfoss VLT 2880
Sicar TOP6

Offline ben_r_

  • Posts: 670
Re: Best Miter saw options?
« Reply #37 on: August 02, 2017, 09:28 PM »
if you want the best of the best mitre saw and the saw stays stationary. go to Omga.

the whole thing is made of cast iron except the saw guard and the power on/off button

I had a T50350 and then upgraded to their double mitre saw.

You wont look at anything else ever again.

List price is $4000 USD for a base model.


The Omga 1P300 is only $1747 USD.
If at first you don't succeed, redefine success!

Offline online421

  • Posts: 64
Re: Best Miter saw options?
« Reply #38 on: August 02, 2017, 09:31 PM »
if you want the best of the best mitre saw and the saw stays stationary. go to Omga.

the whole thing is made of cast iron except the saw guard and the power on/off button

I had a T50350 and then upgraded to their double mitre saw.

You wont look at anything else ever again.

List price is $4000 USD for a base model.


The Omga 1P300 is only $1747 USD.

thats an option. I was referring to the T50 I had.
Robland NX410Pro
Masterwood OMB1V
Omga AL129
SCM 5 RCS110
Chicago Pneumatics CPRS10500
Ceccato CDX 12
Holytek DC006
Festool DF700XL, CT36, LEX3
JLT 190BM2, 79K10
Danfoss VLT 2880
Sicar TOP6