Author Topic: My new router bits arrived in... oil?  (Read 979 times)

0 Members and 1 Guest are viewing this topic.

Offline SilviaS7

  • Posts: 25
My new router bits arrived in... oil?
« on: July 31, 2018, 05:52 PM »
Hi all, I'm a super baby woodworker and I have yet to use a router and router table combo I purchased in June (I will be using it in the next few weeks on my current project).  Anyway, I just ordered a three router bit set and inside the packaging, each of the router bits is totally covered in some kind of oil.  Is this normal?  I've only purchased two other bits previously, and they each arrived in a fancy hard plastic box and no apparent oil.  This new set is just in a plastic housing, nothing fancy (think like a clamshell plastic case, but not impossible to open).  I just don't know if I need to be concerned about sending them back for a return, since they just arrived yesterday.  I'd rather not say the retailer because I don't want to paint anyone in a bad light if I'm just a big dumb baby who doesn't know any better.  :) 

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline threesixright

  • Posts: 37
Re: My new router bits arrived in... oil?
« Reply #1 on: July 31, 2018, 06:24 PM »
I think its normal.

Most of the time iron/metal has something against rust / oxidation. You can/should clean it off. I clean my metal parts with Ballistol.

Anyway. My thoughts, not 100% sure ;-)



Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 11557
Re: My new router bits arrived in... oil?
« Reply #2 on: July 31, 2018, 07:42 PM »
Probably just extra protection against rust.  Clean them and use them. No worries.

Peter

Offline Untidy Shop

  • Posts: 2672
Re: My new router bits arrived in... oil?
« Reply #3 on: July 31, 2018, 08:33 PM »
I have found this to be quite common if bits and blades are from Taiwan. Often these same bits and blades are also wrapped in wax paper. Rather have this minor inconvenience than rust.

In my fathers time as a carpenter in the mid C20 nearly all manufacturers delivered blades this way.

Just clean them before use.
« Last Edit: July 31, 2018, 08:37 PM by Untidy Shop »
If you don't like Signatures, just go to Look and Layout and tick No Signatures.

“The test of the machine is the satisfaction it gives you. There isn't any other test. If the machine produces tranquility it's right. If it disturbs you it's wrong until either the machine or your mind is changed.”
― Robert M. Pirsig, Zen and the Art of Motorcycle Maintenance: An Inquiry Into Values

Offline Alanbach

  • Posts: 168
Re: My new router bits arrived in... oil?
« Reply #4 on: July 31, 2018, 09:47 PM »
Just be careful as you clean them off as they are super sharp. If it’s cosmoline (usually dark yellow brownj it greasy and sticky at the same time. Mineral spirits will also clean it and most protectants. Sometimes the sharp edges are also dipped in a rubbery sort of plastic. I usually make a few cuts with a razor knife to make that stuff easier to remove safely. Again, be super careful as it’s really sharp under there.

Offline SilviaS7

  • Posts: 25
Re: My new router bits arrived in... oil?
« Reply #5 on: July 31, 2018, 10:14 PM »
Thank you so much everyone for your help!  Glad to know this isn't unusual at all.  I will also take care when cleaning the bits to make sure I don't cut myself.

Offline tallgrass

  • Posts: 741
Re: My new router bits arrived in... oil?
« Reply #6 on: August 01, 2018, 03:24 AM »
I use a rust inhibitor after cleaning off the packing oil. Better oil than rust.