Author Topic: Planer/Jointer Combo Axminster AT260PT/AT107PT???  (Read 590 times)

0 Members and 1 Guest are viewing this topic.

Offline saands

  • Posts: 9
Planer/Jointer Combo Axminster AT260PT/AT107PT???
« on: November 03, 2018, 06:13 PM »
Hello everyone,

I have been getting wonderful information from you at the forum and I hope I can gain your input on a decision.

I have a very small woodworking shop (1 car garage - about 10ft by 20ft). I am looking into purchasing a planer/jointer combo and have been looking at the Axminster Trade AT260PT/AT107PT Planer Thicknesser.

1. Has anyone had one of these? If you do, what is your opinion about it?
2. I live in the U.S. and I am wondering what it might cost to have something this size shipped to the US (New England). I am also wondering about customs duties?

Any insights would be greatly appreciated.

Thank you.
saands

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline lwoirhaye

  • Posts: 234
Re: Planer/Jointer Combo Axminster AT260PT/AT107PT???
« Reply #1 on: November 03, 2018, 06:48 PM »
That's a 10" wide machine.   I have owned 5 different jointer/planer combos and it seems to me that you get what you pay for with them.   I got all mine used.   I still have two - a little KITY 6" portable machine and a 16" Knapp.   

If you're looking for economy I'd say get a used 6" or 8" jointer and a benchtop planer while you keep your eye out for a used combo.   The INCA 10" machines with the 42" tables are nice machines if you can find one for sale where the seller isn't fetishizing it as a collectible.

Most woodworkers with room for separate machines I'd advise to skip the combo.   That said, with some of them you get a very nice  jointer.   

I think bringing a single machine overseas may not make sense financially, and if you haven't examined the machine yourself it can be hard to tell what kind of quality you'll be getting.   Some collectors do ship machines from Europe to the usa,  but that's usually Rolls Royce type stuff like Wadkin.

Getting any kind of warranty service or support from a seller without an office in the usa may be a pain, if that's a reason you are looking at a new machine.

Offline RobBob

  • Posts: 1328
Re: Planer/Jointer Combo Axminster AT260PT/AT107PT???
« Reply #2 on: November 03, 2018, 09:21 PM »
@Peter Parfitt

Peter might know something about these.
« Last Edit: November 04, 2018, 07:12 PM by RobBob »

Offline saands

  • Posts: 9
Re: Planer/Jointer Combo Axminster AT260PT/AT107PT???
« Reply #3 on: November 04, 2018, 05:56 PM »
Thank you so much for your input. Given your feedback and what I've heard from others I've talked to, I think I am going to try to squeeze an individual planer and a jointer into my shop.

Again, thanks,
saands