Author Topic: Skilsaw wormdrive frequency  (Read 589 times)

0 Members and 1 Guest are viewing this topic.

Offline shed9

  • Posts: 461
Skilsaw wormdrive frequency
« on: November 09, 2018, 04:17 AM »
Anyone with a Skilsaw wormdrive who can tell me what the frequency rating of it is. Wondering if I can run one on a 110 transformer here in the UK.

I know there are cordless versions but ideally looking for mains.

Any help appreciated.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Bob D.

  • Posts: 1153
Re: Skilsaw wormdrive frequency
« Reply #1 on: November 09, 2018, 05:52 AM »
There are a number of different models in their current lineup. Used to be just the one, tried and true Skilsaw, the 77. Now they have at least a half dozen models, some that cut metal, even a worm drive jobsite table saw.

You didn't mention which particular model you were looking at or if you had an older model. Mine is over 20 years old and still going strong, but weighs a ton compared to the newer models.

Anyway, I went to their website and looked at two different manuals and there was no mention of power requirements, current draw, etc. It does say on the website that it draws 15A, but doesn't give a voltage or frequency. No specs page in the manuals either.

Probably best to drop them an email or message on FB. They respond there in a reasonable amount of time. I have asked them a couple questions on their new recip saw and got a reply in an hour or two. But I have found that the people tending to their FB presence don't always have  a depth of knowledge to answer all questions and you may have to wait for an answer.
-----
It's a table saw, do you know where your fingers are?

Offline Farming_Sawyer

  • Posts: 124
  • Sawyer, builder, winemaker, farmer, chef
    • Foley's Custom Sawmill
Re: Skilsaw wormdrive frequency
« Reply #2 on: November 09, 2018, 06:08 AM »
If your buying a unit from the States, it will be 60hz. Running it on 50hz means the motor will try 20% slower... Ie, less power.
I had a Skillsaw more or less attached to my right arm for years.... They are heavy, noisy, and lack finesse. I wish the HK 55 existed 30yrs ago.....
CT 26E, RO125, sys-mft, sys-toolbox, a bunch of 30 year old tools I'm looking to replace.

Offline shed9

  • Posts: 461
Re: Skilsaw wormdrive frequency
« Reply #3 on: November 09, 2018, 07:13 AM »
Apologies people, I should have said which model. I'm looking at a classic 77 model.

Didn't know they did a TS, cool idea. I'll drop them a note on FB as well, that makes sense.

I have looked for manuals and / or spec sheets to determine the frequency but can't find anything.

Some US 110 tools have 50/60hz specs hence asking if this is the case with the 77. I know this is a heavy saw and probably dated design but still on my list.

Thanks both, appreciated.

EDIT: Just found it, it is 60hz as already noted. I found a parts supplier and looked for a nameplate. For reference, its 120V / 60Hz / 13A (HD77 model).

Thanks again.


« Last Edit: November 09, 2018, 07:20 AM by shed9 »

Offline RJNeal

  • Posts: 382
Re: Skilsaw wormdrive frequency
« Reply #4 on: November 09, 2018, 07:22 AM »
Before you use it , check the gear box oil level. It seems that the factory don’t like to fill them up to operating level.
Rick.
Have you walked your saw today?