Author Topic: My DIY 8020 MFT  (Read 1842 times)

0 Members and 1 Guest are viewing this topic.

Offline modeller

  • Posts: 16
    • Modeller | modern modular shelf system
My DIY 8020 MFT
« on: February 17, 2019, 05:53 PM »
I thought some of you might be interested in seeing how my 8020 MFT works with the woodpecker router jig and some Bessey track/table clamps. they fit into the woodpecker rails with a bit of sanding and I use parf dogs with nuts to attach the woodpecker router jig on edge


https://www.dropbox.com/sh/wbyq3ww7zby4wzm/AADoJrZm74PCfffHD9mPJYqqa?dl=0
293045-0

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Renovatedspaces

  • Posts: 60
Re: My DIY 8020 MFT
« Reply #1 on: February 18, 2019, 02:45 PM »
Nice set up. how do you like  the Vac Sys? I’m on the fence about getting one.
Kapex, CT 26e, Installers clean up kit, RO 125, MFK 700, Domino 500, Carvex 420 with Kit, TS 75

Offline modeller

  • Posts: 16
    • Modeller | modern modular shelf system
Re: My DIY 8020 MFT
« Reply #2 on: February 18, 2019, 05:51 PM »
I didn't use the vac sys much until I mounted it to the side of my bench, flush with the top. now it indispensable. I bought it at the same time as my Conturo. I had a large job with edge banding so I could justify the cost. I've even used it once when I cut a piece too short so I banded on 3mm edging to fix my mistake!
« Last Edit: February 18, 2019, 05:56 PM by modeller »

Offline stickman

  • Posts: 23
Re: My DIY 8020 MFT
« Reply #3 on: February 18, 2019, 08:27 PM »
Quote
seeing how my 8020 MFT works with the woodpecker router jig and some Bessey track/table clamp

I am super interested. How big is your table? Do you have a cut list you want to share? I really want an 80/20 based assembly table but every time I try to build a cut list to order I give up lol
KS-120 | TS-75EQ | DF-500Q | XLDF-700 | RO-150FEQ | RO-90DX | HKC-55EQ-FSK420 | EBQ-420D | MFT/3 | CT-26 | CT-SYS | T18+3 | OF-1400EQ |  TSC55 REB PLUS | HL 850 | RAS-115 | VECTURO OS 400 | PDC 18/4 | LR32-SYS | SYS-ROLL 100

Offline modeller

  • Posts: 16
    • Modeller | modern modular shelf system
Re: My DIY 8020 MFT
« Reply #4 on: February 20, 2019, 12:05 AM »