Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: VL Table with saw trouble.  (Read 1757 times)

0 Members and 1 Guest are viewing this topic.

Offline chucklesuk

  • Posts: 12
VL Table with saw trouble.
« on: May 19, 2019, 05:40 PM »
Hi All

I have the VL table extn for the MFT. The VL has a strip of plastic trim on the out feed side (L/H side looking from the front)   But when using the TS55 saw in my case with of course the table saw plate fitted timber (often Ply) will hit the plastic strip as its being fed through and stop. The timber has to be lifted a fraction of an inch to free it not something I like to do with a running saw. Also not something I would expect from a high class tool company.  I have removed the plastic strip so now the table edge is missing.
Has anyone had this problem? Or found a solution?

Tried calling Festool and eventually they put me in touch with the area rep who did phone me and promised to come and look but never showed up.  I'm not a happy bunny having spent a considerable amount of money on their products.   [mad]
« Last Edit: May 19, 2019, 05:46 PM by chucklesuk »

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline GarryMartin

  • Posts: 1807
Re: VL Table with saw trouble.
« Reply #1 on: May 19, 2019, 05:54 PM »
Do you have a photo? I'm struggling to visualise which piece of plastic from your description.

I only have a single piece of light grey coloured plastic on the outfeed side that runs the entire width of the table. Is that what you mean? Mine is below the surface of the VL/insert plate...


Offline Bert Vanderveen

  • Posts: 535
Re: VL Table with saw trouble.
« Reply #2 on: May 20, 2019, 07:47 AM »
@chucklesuk  On my VL that piece of trim is slightly under the rest of the top (just enough to move a fingernail along). Since you already took it off, you could check it for anomalies and perhaps repair it with a bit of sanding.
Cheers, Bert Vanderveen

TS55 · TS55R · OF1010 · DF500 Mk2 · MFT/3 + TSB1-MW 1000 + VL + CMS TS55 + CMS PS300 + LA-CS 70/CMS · CTL Midi · RTS400 EQ · 2 x CXS Li 1,5 · T15+3 Li 4,2 · TI15 Impact Li 4,2 · Centrotec Sets 2008 + 2015 · PSB300 · LR32-SYS · RO150 · Kapex KS120 · 2 x MFK700 · RO90 · OFK700 · BS75 · OFK500 · OF2200 · CMS-GE … | Mirka 1230L P&C | Hammer A3 31 Silent Power · Hammer N4400 · Hammer HS950 (soon!) 

Offline chucklesuk

  • Posts: 12
Re: VL Table with saw trouble.
« Reply #3 on: May 20, 2019, 08:31 AM »
Thanks for the replies guys.

Y es thats the part in the photo.
I had the problem since day one though I must admit it difficult to actually to see a fault and sometimes I get away with it but it is dangerous and I would like to stay attached to my fingers.

As you suggest I will try some sanding. I didn't do anything at first in case it invalidated the guarantee.  Still very disappointed with the lack of Festool customer service.  I was hoping if others had the same trouble we could get Festool to do something about it.

Thanks again

Brian