Author Topic: Non Festool Hoses  (Read 4125 times)

0 Members and 1 Guest are viewing this topic.

Offline Siskiyou

  • Posts: 2
Non Festool Hoses
« on: June 12, 2019, 10:56 AM »
I just bought a CT 36 Dust Extractor yesterday, my old shop vac is a Craftsman which has a much larger hose that fits perfectly into the intake port on the CT 36. Will using this hose and attachments for shop cleanup and hooking up to my non-Festool  miter saw harm the CT 36 because it is not a non static hose.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline VictorL

  • Posts: 582
Re: Non Festool Hoses
« Reply #1 on: June 12, 2019, 11:02 AM »
Festool makes and sells non-antistatic hoses too.  Shouldn't be a problem for no name hoses.

Re: Non Festool Hoses
« Reply #2 on: June 12, 2019, 01:58 PM »
If you ever want to go higher quality at a low-cost, Bosch makes a $36 non antistatic hose on Amazon that fits all festool tools.

Offline Siskiyou

  • Posts: 2
Re: Non Festool Hoses
« Reply #3 on: June 12, 2019, 03:48 PM »
Thank you both for the help.

Offline todd_fuller

  • Posts: 12
Re: Non Festool Hoses
« Reply #4 on: June 14, 2019, 11:53 AM »
Nilfisk sells a number of anti-static hoses that cost a fair bit less than Festool.

Offline DrD

  • Posts: 416
  • I might not be fast BUT I sure am slow
Re: Non Festool Hoses
« Reply #5 on: June 15, 2019, 09:53 AM »
I think the hose mentioned by Carlson Carpentry above may be this hose: Bosch 16.4 Foot Vacuum Hose, 35mm VAC005.  A couple of years ago I bought one of these for my Kapex; the hose is NON antistatic.  It connects to my CT26 thru an antistatic sleeve, which in turn has a length of Festool antistatic hose going to the CT.  The sleeve allows me to connect either the Kapex (with the non AS hose) or the AS hose on my boom arm which goes over my MFT3s.  Never had any issues, but it doesn't connect directly to the CT either.

Look at the hoses Festool uses on their router table - I believe both hoses are NON-AS.  If that is the case, then by implication one might assume Festool is saying it is ok to connect a NON-AS hose to a CT.
KS12 EB Kapex with Delta Folding Table & FastCap Best Fence; TS75 EQ with Parallel Guide Rail Set (FS-PA 495717 & FS-PA-VL 495718) and FS 800/2, 1080/2, 1400/2 LR32, 1400/2, 1900/2 Guide Rails, and Betterly SLC23 Straight Line Connector; DF500 Q with Assortment Systainer; OF1010 EQ with Fine Adjuster for Guide Stop, WA-OF Angle Arm, UP-OF Edging Plate and SF-OF Chip Deflector (486242); OF1400 EQ with OF1400 Dust Hood x 2, OF 1400  Edge Guide x 2, OF 1400  Guide Stop; LR32 Set; PSB399 EQ; EHL65 E; RAS115.04 E; RS2 E; ETS150/3 EQ; RO150 FEQ; Hand Sanding Block Set; CT26 with assortment of AS and Non-AS Hoses; MFT/3 Table x2; SysLite; Assortment of Quick & Screw Clamps, Consumables, Dogs.

Offline Jim_in_PA

  • Posts: 74
Re: Non Festool Hoses
« Reply #6 on: June 15, 2019, 10:12 AM »
My "soft" Ridgid hose also fits my CT extractor, although I never use the Festool vac for cleanup.
----
ETS 150/3, Rotex 150, OF1010, OF1400, Trion PS 300, TDK-12, CT-22, MFT 1080, TS55, Domino XL DF 700, 8' track, (2) 55" tracks

SCM MiniMax S315WS, FS350, MM16, Camaster Stinger II SR-44 CNC