Author Topic: Repairing door jambs  (Read 1884 times)

0 Members and 1 Guest are viewing this topic.

Offline Gjarman12

  • Posts: 98
Repairing door jambs
« on: August 28, 2018, 09:08 AM »
Hello, we are replacing the doors in our house and our jambs need some work. They were painted white at some point, but also left with what looks like the original finish. The white will chip off as seen in the picture (sort of). We want the jambs white. Any tips on getting a nice white finish on the jambs?284524-0

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline ctvader

  • Posts: 61
Re: Repairing door jambs
« Reply #1 on: August 28, 2018, 09:25 AM »
You could send them down, use a nice primer, sand again, prime again, sand lightly, finish coat 1, sand lightly and then last coat of finish.  I would try to use a BM Satin Impervo (WB) (there are many reviews on other paints - Pro Classic, PPG, etc). 

Offline Cheese

  • Posts: 6259
Re: Repairing door jambs
« Reply #2 on: August 28, 2018, 10:02 AM »
It looks to me like when the jambs were painted, the jambs weren't sanded or they weren't cleaned or both. A good sanding, some primer and 2 top coats should fix that.

Offline RKA

  • Posts: 1664
Re: Repairing door jambs
« Reply #3 on: August 28, 2018, 10:48 AM »
It seems like you're asking two questions.  Correct me if I'm misunderstanding.
1.  How to deal with the chipped paint.  I don't see primer under that chipped paint.  I wonder if they painted right over the wood?  Anyway, scrap away anything remotely loose.  Sometimes you can't tell until you run a scraper over the paint and suddenly paint you thought was adhered just breaks off.  So scrap every inch of those jambs.  Sand, prime, light sand, paint x 2 (as mentioned above).

2.  The stained part of the jamb needs to be painted white.  Use a shellac based primer (stir well before use) to cover up the brown.  2 coats to be safe, sand, paint x 2.

I won't tell you which paint to use, but I will say I've not been happy using Sherwin's new Emerald Urethane trim paint.  It just doesn't level well (or at all it seems).  I suspect a pro painter would find a way to work with it, but I tried with and without Floetrol, good brushes, mohair rollers, foam rollers.  With Floetrol and a roller worked the best, but I won't be using this on trim because it's not leveling well.
-Raj

Offline jobsworth

  • Posts: 5750
  • Festool Baby.....
Re: Repairing door jambs
« Reply #4 on: August 28, 2018, 11:42 AM »
scrape, use spackle or another filler to even the paint out sand smooth check to see if it needs more repeat , prime and paint.

Offline toadjeep

  • Posts: 9
Re: Repairing door jambs
« Reply #5 on: August 28, 2018, 12:15 PM »
Pry the door stops off, sand the frame and stops then reattach and paint.


Sent from my iPhone using Tapatalk

Online Alex

  • Posts: 6054
Re: Repairing door jambs
« Reply #6 on: August 28, 2018, 03:00 PM »
That's some crap paint that's on there if it just flakes off indoors without any weather influences. Normaly you only see this outside where paint is exposed to heavy rain and the burning sun.

Find out if it's only this spot that's flaking or if the entire layer of paint is loose. Use a putty knife or chisel to see how easily you can scrape it away. If it's just this spot than there's not so much to worry about, but if the entire layer is so badly adhered you'll have to remove it entirely.

Offline Gjarman12

  • Posts: 98
Re: Repairing door jambs
« Reply #7 on: August 29, 2018, 09:08 AM »
I picked away a little bit yesterday. The white stuff will probably come off pretty easy once I start. It’s just the corners where it meets the stops that will be tricky, I guess that anyone might take them off. I’ll see how it goes without that. Shellac primer will go on the non painted parts. Thanks.