Author Topic: New CNC spoilboard  (Read 1076 times)

0 Members and 1 Guest are viewing this topic.

Offline Mario Turcot

  • Posts: 932
New CNC spoilboard
« on: March 18, 2019, 08:37 AM »
My CNC spoilboard was over due so I decided to give it a fresh look. The original had a very basic clamping capability. Butt the board against the two pieces and screw the four corners.

The MDF available here is of poop quality but it's just a spoilboard right! Here some material that will be used. Out of a 4'x8' sheet I got enough material to make 3 spoilboards.

I changed my mind about the brass inserts. They look nice for sure but are prone to strip easily so I went with a more sturdy ones that can be installed with allen key instead.

I did a dry fit just for fun  [big grin]

Installing the first strip, easy peazy.

You know the satisfaction when you use a template to bore holes and everything fit perfectly for the first time ever in your life  [eek]

The t-track (6) are 36" long.

And the final result.


Coming soon: I will make some 20mm holes for clamping purpose
« Last Edit: March 18, 2019, 04:58 PM by Mario Turcot »
Mario

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline GarryMartin

  • Posts: 1808
Re: New CNC spoilboard
« Reply #1 on: March 18, 2019, 10:31 AM »
Will you not miss the Z height by laying the new spoilboard on top of the old?

Offline Mario Turcot

  • Posts: 932
Re: New CNC spoilboard
« Reply #2 on: March 18, 2019, 10:47 AM »
Will you not miss the Z height by laying the new spoilboard on top of the old?

Effectively, it went from 3" to 2" 1/4 of travel. I went that path because all the boards I have carved with the CNC since the last 2 years, were under 25mm thick. Most of the time I use 1/32" to 1/4" bits and those are under 1/2" to 1" of cutting edge. Cutting deeper with the machine I have is kinda tricky. Feasible but I don't see any scenario I would.

If ever I get into CNC more seriously, I will get a full size machine like the Axiom Precision or similar.

For me that CNC machine was an experiment. To see if I could DIY a kit and how useful a CNC can be in my situation. The DYI build took 2.5hrs plus some wire management. Lately I add a zeroing plate to it and job setup is a breeze compare to previously. Oh and a wireless motion controller is a must [big grin]
« Last Edit: March 18, 2019, 10:54 AM by Mario Turcot »
Mario

Offline Cheese

  • Posts: 6365
Re: New CNC spoilboard
« Reply #3 on: March 18, 2019, 11:14 AM »
I like it Mario...nice job.  It reminds me of a Shelix cutter head, you only replace the damaged item. [big grin]

Offline Mario Turcot

  • Posts: 932
Re: New CNC spoilboard
« Reply #4 on: March 25, 2019, 08:39 AM »
Thank you Cheese.

Here a picture of the spoilboard finished. 8x6 dog holes grid. I have two 3mm holes bored on the back of each strip. Haven make the 20mm hole because I don't see using that part yet. Fun fack, I bored all 3mm & 20mm holes with the CXS on one single batteries not even full charged. Boring was really easy.

Blue shapes: They are from Yellowshedbox. L angle to butt your material and cam clamps. They are a very very nice fit into the UJK Parf guide system holes.
Yellow shapes: Again from Yellowshedbox. Easy to pull-out dogs with extreme nice fit.
Bench-Dog Fence: I put it there kust so I can test their dogs. Very nice fit there too.

UJK Parf Bit Tear-out under MDF boring like no tomorrow. I was testing on MDF and bored a hole without worrying (full blown) about tear out. The small adjacent hole is from a Brad Point bit.


L.V. dogs

Three different dogs from L.V. none have a good fit. The stainless steel Super Parf Dog is a ok fit but still have some movement. I will have to get me some TSO Dogs  [big grin]
« Last Edit: March 25, 2019, 09:12 AM by Mario Turcot »
Mario