Author Topic: Vac Sys mobile cart  (Read 4251 times)

0 Members and 1 Guest are viewing this topic.

Offline travisj

  • Posts: 363
Re: Vac Sys mobile cart
« Reply #30 on: March 06, 2019, 09:55 PM »
I am a fan of that cart.  Nicely done.  If only I had the room...


Sent from my iPhone using Tapatalk

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline thedevme

  • Posts: 105
Re: Vac Sys mobile cart
« Reply #31 on: March 08, 2019, 01:12 AM »
@DynaGlide  I haven't had to the time to reply yet but this build is absolutely beautiful.  Did you wing it for the top since this is not the same as the original model.  I am literally planning on doing this build next week I absolutely love it.

Very kind words. I haven't had a lot of use with the cart yet but I'm thrilled with how it has turned out. What do you mean about winging the top?

Here are the differences from Neil's design:

Vac Sys integration (different drawer, holes cut for hose routing)
No 20mm holes in top
I used plywood for the entirety of the frame for the MDF top. Neil used plywood for the interior frame but the outer perimeter that receives the T track he used maple hardwood. I don't have the tools to mill lumber for that purpose so I went with what I had. The top frame has a little flex in the middle if you lean on it but I don't think it will be an issue. I did reinforce the middle underneath the top with a cross member using pocket screws.

The dimensions overall are pretty much the same as well I may have changed this or that as I went. I did try to stick to the overall height of his since it's designed to clear the MFT/3 table ~900mm.

I have the ability to bore the 20mm holes in the MDF I just chose not to. I figure I could use a bench surface without holes in it in my shop.

The shop is still growing. Haven't been in the house a year even.




Very nice.  What I meant by winging it - I thought you deviated from the original plans. Looks like you didn't I am actually going to pick up the lumber for this soon and mimick exactly what you did.  Going to put all these dimensions into a cut list and do it.  I will post pics when I am done thank you again @DynaGlide you did a beautiful job. By the way, what kind of hooks are you using on your wall for your festool tracks?
« Last Edit: March 08, 2019, 01:26 AM by thedevme »

Offline DynaGlide

  • Posts: 475
Re: Vac Sys mobile cart
« Reply #32 on: March 08, 2019, 05:56 AM »
I did make the top flush at the front and back. Neil did not.

The hooks are rubber coated from home Depot. They have a large screw on the other end. It's an okay arrangement for now.
Instagram @matts.garage

Offline DynaGlide

  • Posts: 475
Re: Vac Sys mobile cart
« Reply #33 on: March 17, 2019, 02:36 PM »
I just got back from Gregory Paolini class and while in Asheville looking around look what I found



Calavera stopped producing these a while back. I wanted one for the cart and was glad to have found it.
Instagram @matts.garage

Offline TSO Products

  • Retailer
  • *
  • Posts: 847
    • TSO Products
Re: Vac Sys mobile cart
« Reply #34 on: March 17, 2019, 07:20 PM »
Matt, that is a very nicely executed project. Has to be motivation for others to undertake something like that. Fellows, like NeilC, ever so willing to share information makes it all the more encouraging.  Where else but on the FOG?

My hat's off to you -  and Neil!

Hans
TSOproducts.com

Home of the GRS-16 and GRS-16 PE  plus TPG Parallel Guide -  the MTR-18 Triangle - TDS-10 Dog Stop and GRC-12 Guide Rail Connector; Work Holding solutions plus AXMINSTER UJK in the USA

Offline neilc

  • Posts: 2727
Re: Vac Sys mobile cart
« Reply #35 on: March 18, 2019, 06:50 PM »
Matt - Great idea on the Calavera holder.  I have one but never thought about placing on the side of the bench for FT clamps!

Hans - Thanks for the shout out!  Yes this is a giving community.  Makes it easy to contribute ideas and inspiration! 

Offline DynaGlide

  • Posts: 475
Re: Vac Sys mobile cart
« Reply #36 on: March 18, 2019, 07:36 PM »
@TSO Products Very kind words Hans.

Instagram @matts.garage