Feature Wall

tiralie

Member
Joined
Jan 26, 2010
Messages
3,617
I am starting this project late September and thought I would post the drawings and some of the details here.
[attachimg=1]

through the dinning room to the front door....

[attachimg=8]

As you can see there is a door in the middle of the wall that allows access to a passageway that has some closets and storage a den as well as an interior door to the garage.

[attachimg=3]

The wall faces a dinning room that is flanked by the two pillars you see in the photo.

The client wanted to turn this wall in their home into a "feature" wall by adding some ledger stone and wood paneling.

I submitted 2 designs, one without a door and one with a "hidden" door.

[attachimg=4]

[attachimg=5]

Design with "hidden" Door

[attachimg=6]

[attachimg=7]

The client picked the design with the hidden door. I will be using some Soss Invisible closers and hinges for the door. The paneling will be Ash in ebony.
Tim
 

Attachments

  • FromDRm.jpg
    FromDRm.jpg
    29 KB · Views: 2,866
  • ToFrtDr..jpg
    ToFrtDr..jpg
    23.9 KB · Views: 2,812
  • FeatWall2B.jpg
    FeatWall2B.jpg
    33.5 KB · Views: 2,792
  • FeatWall2A.jpg
    FeatWall2A.jpg
    34.2 KB · Views: 2,855
  • FeatWall1B.jpg
    FeatWall1B.jpg
    35.3 KB · Views: 2,783
  • FeatWall1A.jpg
    FeatWall1A.jpg
    34.4 KB · Views: 2,901
  • ToKitchen.jpg
    ToKitchen.jpg
    22 KB · Views: 2,792
  • ToFrtDr..jpg
    ToFrtDr..jpg
    23.9 KB · Views: 238
I'm certain it will look better than the renderings when you're done.

Tom
 
Joseph C said:
If you haven't heard of the Tectus hinges yet, (there is also a version by Sugatsune,) you might want to check them out as an alternative to the Soss. 

Thanks Joseph.
I read the ThisisCarpentry article when it first came out and like that system. I looked at Tectus, Sugatsune and Rixon but because of the self closer feature that I sold to the client I believe I am going to have to use the Soss. I would really prefer to use a Tectus hinge but with 3 children in the family and fair amount of traffic in the closets that door is going to be left open a lot if there is not self closing feature. The door is going to be a left swinging door so I believe I am ok with the offset to the inside of the door which will allow me to add the paneling and still get a "flush" invisible door.

It has been suggested that I use a solid wood, (not chip board) stave core door for this application.
Tim
 
Here is a video of the hidden door, just before I put the last panels in.
The wall is mostly finished now just in time for Xmas, a few finish details to complete. Then on to the stair landing panels.


 
Very nice Tim.  Must have missed this thread before.  What system did you use for attaching the panels to the wall ?
 
woodguy7 said:
Very nice Tim.  Must have missed this thread before.  What system did you use for attaching the panels to the wall ?

Thanks Alan.
I used two different approaches for the wall and the door. The 3/4" panels are hung on the wall with monarch mf250-Z- clips. The space between the panels is 3/8" so the mf250 with a 1/4" lift off work well. I glue 1/4" thick reveal strips on the wall with PL 200 and pin to hold while the glue sets. I shim out the wall using some glazier shims that come in 1/16, 1/8 and 1/4" thicknesses.

I originally ordered a 1 3/8" stave core (solid) door but the supplier ordered a 1 3/4" door which with the addition of the panels and revel strips was going to make for a very thick door.
I decided to route the revel strips into the door and then have the door hang flush with the 1/4" strips mounted to the wall. This saved some thickness on the door but it still ended up a 2 1/2" thick with the panels.
The Panels on the door are shimmed out with wood and glued with PL 200 and pinned with a 23 gauge pin. The 23 gauge pins allow me to adjust the panels. I may have to put some 16 gauge nails on those panels to hold it on the door.

Tim
 
Thanks Max and Baremeg55
Here is a (rather poor) picture of the finished wall. I will upload a better one later.

[attachimg=1]

Here is the routed hole in the casing/2x6 for one of the four Soss 216  hinges

[attachimg=2]

... and the Soss hinge in the door.

[attachimg=3]
 

Attachments

  • CrappyFeatureWallPic.jpg
    CrappyFeatureWallPic.jpg
    313.4 KB · Views: 1,742
  • RoutedSoss.jpg
    RoutedSoss.jpg
    170 KB · Views: 1,733
  • SossHingeInDoor.jpg
    SossHingeInDoor.jpg
    267 KB · Views: 1,758
Tim Raleigh said:
Here is a video of the hidden door, just before I put the last panels in.
The wall is mostly finished now just in time for Xmas, a few finish details to complete. Then on to the stair landing panels.



Very nice Tim. I bet it was a fun and challenging project to undertake.

JC
 
This is a creative solution that is very well done and really enhances the space.  The homeowners are fortunate to have you working on their project.  Top notch!

Thank you for sharing!
 
JCLP said:
Very nice Tim. I bet it was a fun and challenging project to undertake.

Thanks JC.
Yep, this project was/is challenging and kicked my #ss.
For a wall, there is a lot of information in that installation.
Tim
 
mike_aa said:
The homeowners are fortunate to have you working on their project.

Thanks Mike.
When the homeowner looked at the photo from my phone (posted above), she said "it looks like Houzz".
She was happy.
Tim
 
After the client hired me to make the feature wall, they asked me to also look at doing the stairwell.
I finished it this week.
Here's a cell phone photo, I will take a better one later.
[attachimg=1]
 

Attachments

  • StairWellPanel2.jpg
    StairWellPanel2.jpg
    779.3 KB · Views: 1,172
I'm not ashamed to say I dont know what I'm looking at with the last photo, confusesnmenfor some reason my eye can'te sense of it!
 
rizzoa13 said:
I'm not ashamed to say I dont know what I'm looking at with the last photo, confusesnmenfor some reason my eye can'te sense of it!

rizzoa, Thanks for the feedback. You are right.
It is difficult to figure out what is going on there. I will post some better pics when I get back in there.

Tim
 
Back
Top