HandyDen
Member
- Joined
- Sep 26, 2017
- Messages
- 53
I have a few Festool accessories that are in good condition, but don’t fit into my work system anymore. I prefer local pickup in the Madison, WI, area, but I can certainly ship the LR 32 kit or the MFT angle kit. I also have a shipping box for the Kapex Extension Wings, but that can't be cheap to ship(?).
MW1000 Mobile Cart - $375
- Easily transports multiple systainers, even up/down stairs
- Slide-out tray to access commonly used systainer
- Small storage cubby below
- MFT work surface on top, with a variety of clamping areas on top and side
- Accepts MFT Extensions (not included, but available below)
- I can load this up with Systainers, tip in into my van and transport it laying down without spilling anything
- Used for about a year, so it has some wear, but is still in perfect working order
![ATTACH]](http://[ATTACH]1[/ATTACH])
MFT Extensions - $175/each (2 available)
- 20” x 40” work surface that can be added to the MW1000 cart above, or attached to your MFT
- Very lightweight and portable mobile worktable solution
![ATTACH]](http://[ATTACH]2[/ATTACH])
![ATTACH]](http://[ATTACH]3[/ATTACH])
Kapex UG Extension Wing Set - $475 (+ actual shipping)
- adds 94” of infeed/outfeed support to your Kapex miter saw
- Can be attached to the UG Cart and/or the MFT Mini/Kapex version
- Dead-on accuracy using the stop flag - never measure your stock again
- Imperial measurement version (I’m only selling this because I switched to all metric)
- Comes with straps for easy transportation
- Used daily for about a year, but still in perfect working order
![ATTACH]](http://[ATTACH]4[/ATTACH])
![ATTACH]](http://[ATTACH]5[/ATTACH])
MFT Protractor Angle Unit - $80/each shipped CONUS (2 available)
- This is everything that makes an “MFT Basic” into a full-blown “MFT Multi-Function Table” for cross cutting
- Includes protractor head, fence rail, fence stop and fence clamp, but does not include the track saw guide rail
![ATTACH]](http://[ATTACH]6[/ATTACH])
![ATTACH]](http://[ATTACH]7[/ATTACH])
LR32 Hole Drilling Set - SOLD
- Guide plate, centering mandrel, linear stops and two edge stops for drilling European 32 mm grid pattern holes in shelves and cabinets
- This is the boxed set (not the one in a Systainer)
![ATTACH]](http://[ATTACH]8[/ATTACH])
Thanks for looking!
MW1000 Mobile Cart - $375
- Easily transports multiple systainers, even up/down stairs
- Slide-out tray to access commonly used systainer
- Small storage cubby below
- MFT work surface on top, with a variety of clamping areas on top and side
- Accepts MFT Extensions (not included, but available below)
- I can load this up with Systainers, tip in into my van and transport it laying down without spilling anything
- Used for about a year, so it has some wear, but is still in perfect working order
MFT Extensions - $175/each (2 available)
- 20” x 40” work surface that can be added to the MW1000 cart above, or attached to your MFT
- Very lightweight and portable mobile worktable solution
Kapex UG Extension Wing Set - $475 (+ actual shipping)
- adds 94” of infeed/outfeed support to your Kapex miter saw
- Can be attached to the UG Cart and/or the MFT Mini/Kapex version
- Dead-on accuracy using the stop flag - never measure your stock again
- Imperial measurement version (I’m only selling this because I switched to all metric)
- Comes with straps for easy transportation
- Used daily for about a year, but still in perfect working order
MFT Protractor Angle Unit - $80/each shipped CONUS (2 available)
- This is everything that makes an “MFT Basic” into a full-blown “MFT Multi-Function Table” for cross cutting
- Includes protractor head, fence rail, fence stop and fence clamp, but does not include the track saw guide rail
LR32 Hole Drilling Set - SOLD
- Guide plate, centering mandrel, linear stops and two edge stops for drilling European 32 mm grid pattern holes in shelves and cabinets
- This is the boxed set (not the one in a Systainer)
Thanks for looking!
