chippendale
Member
- Joined
- Feb 5, 2017
- Messages
- 5
Used for ony one job. This track saw kit combines what FOG members say as the best value:
Makita SP6000 track saw with a 12 Amp motor (Festool's TS55 has a 10 Amp motor) - $500 on sale with Makita 55" track;
Makita 48-tooth 6.5" blade, just sharpened locally by Quality Saw and Knife;
Makita 55" track, Part No. 194368-5 (http://bit.ly/2uJQOIp);
Festool LR32 55" track, FS 1400/2-LR 32, Part No. 496 939 - $180 CDN;
Makita Guide Rail Connector Kit, Part No. P-20177, with all 4 connectors, all 8 hex screws, hex wrench, and case - $50 CDN;
Makita Guide Rail Bag for 55" Guide Rails - Part No. P-67810 - $50 CDN;
Dewalt Tracksaw Track Clamps, DWS5026 (faster than Festool clamps) -http://bit.ly/2v3B2U0 - $60 CDN;
Makita Dust Bag, Part No: 122562-9;
Rip Dogs Rip Guide - Complete Set -http://www.ripdogs.com/rip-guides-complete-set/ ($140 USD + shipping = $200 CDN)
Two - Incra Rails 10" long for Rip Dogs - $20;
Two - Incra Rails 26" long for Rip Dogs - $20;
Festool Systainer 4 - $122
Replacement cost is $1200 + taxes. If you went all Festool, it is $1,584 + taxes.
Joining the two 55" rails allows you to rip a 4' x 8' sheet. The Rip Dogs allow you to cross-cut small pieces. Both 55" tracks and the Rip Dogs fit into the Makita rail bag. I did not take a picture of the included Festool SYS 4 container. There is some paint overspray on the SYS 4.
Selling all for $800 CDN. Local sale, cash only.
Makita SP6000 track saw with a 12 Amp motor (Festool's TS55 has a 10 Amp motor) - $500 on sale with Makita 55" track;
Makita 48-tooth 6.5" blade, just sharpened locally by Quality Saw and Knife;
Makita 55" track, Part No. 194368-5 (http://bit.ly/2uJQOIp);
Festool LR32 55" track, FS 1400/2-LR 32, Part No. 496 939 - $180 CDN;
Makita Guide Rail Connector Kit, Part No. P-20177, with all 4 connectors, all 8 hex screws, hex wrench, and case - $50 CDN;
Makita Guide Rail Bag for 55" Guide Rails - Part No. P-67810 - $50 CDN;
Dewalt Tracksaw Track Clamps, DWS5026 (faster than Festool clamps) -http://bit.ly/2v3B2U0 - $60 CDN;
Makita Dust Bag, Part No: 122562-9;
Rip Dogs Rip Guide - Complete Set -http://www.ripdogs.com/rip-guides-complete-set/ ($140 USD + shipping = $200 CDN)
Two - Incra Rails 10" long for Rip Dogs - $20;
Two - Incra Rails 26" long for Rip Dogs - $20;
Festool Systainer 4 - $122
Replacement cost is $1200 + taxes. If you went all Festool, it is $1,584 + taxes.
Joining the two 55" rails allows you to rip a 4' x 8' sheet. The Rip Dogs allow you to cross-cut small pieces. Both 55" tracks and the Rip Dogs fit into the Makita rail bag. I did not take a picture of the included Festool SYS 4 container. There is some paint overspray on the SYS 4.
Selling all for $800 CDN. Local sale, cash only.
