New Rol-air JC10

[Tim Sproul]

There are different set screws for adjusting the "on" pressure and "off" pressure.  Definite would not want the "off" pressure to be greater than factory - I think 120 psi.

The compressor cycles more - but a 1 man crew won't overwork the compressor - assuming you are using this little compressor appropriately.  Smaller jobs and jobs requiring infrequent nailing.

This is the JC10 or the PC1010 you're talking about? I've just ordered a PC1010 for myself because of its quietness, size and easy portability. If I can get it to attain 120 psi without it  running constantly, then it will fill all my current needs.

I have the Senco 1010 and do not have the Rolair jc10 so my comments are restricted to the Senco.

On mine, the pressure set screws seemed to adjust the pressure when the compressor cycled on and when it cycled off.

The Rolair sounds like a smaller version of the 4 gallon Thomas compressor I have - dual compression pistons running off one motor.  My only gripe is I wish Thomas would use higher pressure compressor - 150 or 175 or even 200 psi instead of just 125.

 

[JLB builders LLC]

I have the Senco pc0968 twin tank 1.5 hp 2.5 gallon, still light and I used it 3 weeks ago to install oak hardwood floor in a hallway with my pneumatic flooring gun. worked fine and kept up.

The Senco 1010 is super light and made for trim guns and pin nailers. My buddy has a few of them and they serve his purpose of running into a Lowes or Home Depot store to do a display.

Depends on your needs, the JC10 sounds like a great compressor. If my Senco dies I will try one out. For the record I have a wheelbarrow style Emglo with an electric motor that I built. It is whisper quiet (not much louder than the JC10) but a beast to move around. It had a honda gas motor at one time and I ended up with a motor from a compressor out of a Hechs that was remodeled. I believe it was a 20-30 gallon tank and used for the Sprinkler system to keep it pressurized or something like that. Anyway I use the Senco for anything, besides roofing and heavy framing so I do not have to move the Emglo.

The specs seem pretty close to each other JC10 40lbs Senco 38lbs, JC10 seems quieter  [smile] So I think the JC10 should be compared to the Senco PC0968 and not the 1010

http://www.cposenco.com/senco-pc0968-1-5-hp-2-5-gallon-oil-less-hand-carry-air-compressor/sennpc0968,default,pd.html?start=1&cgid=senco-compressors

 

[Ken Nagrod]

I have the Senco pc0968 twin tank 1.5 hp 2.5 gallon, still light and I used it 3 weeks ago to install oak hardwood floor in a hallway with my pneumatic flooring gun. worked fine and kept up.

The Senco 1010 is super light and made for trim guns and pin nailers. My buddy has a few of them and they serve his purpose of running into a Lowes or Home Depot store to do a display.

Depends on your needs, the JC10 sounds like a great compressor. If my Senco dies I will try one out. For the record I have a wheelbarrow style Emglo with an electric motor that I built. It is whisper quiet (not much louder than the JC10) but a beast to move around. It had a honda gas motor at one time and I ended up with a motor from a compressor out of a Hechs that was remodeled. I believe it was a 20-30 gallon tank and used for the Sprinkler system to keep it pressurized or something like that. Anyway I use the Senco for anything, besides roofing and heavy framing so I do not have to move the Emglo.

The specs seem pretty close to each other JC10 40lbs Senco 38lbs, JC10 seems quieter  [smile] So I think the JC10 should be compared to the Senco PC0968 and not the 1010

http://www.cposenco.com/senco-pc0968-1-5-hp-2-5-gallon-oil-less-hand-carry-air-compressor/sennpc0968,default,pd.html?start=1&cgid=senco-compressors

That's what I had said (post #10).   [smile]

 

[Sean7a]

There are different set screws for adjusting the "on" pressure and "off" pressure.  Definite would not want the "off" pressure to be greater than factory - I think 120 psi.

The compressor cycles more - but a 1 man crew won't overwork the compressor - assuming you are using this little compressor appropriately.  Smaller jobs and jobs requiring infrequent nailing.

This is the JC10 or the PC1010 you're talking about? I've just ordered a PC1010 for myself because of its quietness, size and easy portability. If I can get it to attain 120 psi without it  running constantly, then it will fill all my current needs.

I have the Senco 1010 and do not have the Rolair jc10 so my comments are restricted to the Senco.

On mine, the pressure set screws seemed to adjust the pressure when the compressor cycled on and when it cycled off.

The Rolair sounds like a smaller version of the 4 gallon Thomas compressor I have - dual compression pistons running off one motor.  My only gripe is I wish Thomas would use higher pressure compressor - 150 or 175 or even 200 psi instead of just 125.

Tim, what application do you want the higher pressure for?

 

[JLB builders LLC]

I have the Senco pc0968 twin tank 1.5 hp 2.5 gallon, still light and I used it 3 weeks ago to install oak hardwood floor in a hallway with my pneumatic flooring gun. worked fine and kept up.

The Senco 1010 is super light and made for trim guns and pin nailers. My buddy has a few of them and they serve his purpose of running into a Lowes or Home Depot store to do a display.

Depends on your needs, the JC10 sounds like a great compressor. If my Senco dies I will try one out. For the record I have a wheelbarrow style Emglo with an electric motor that I built. It is whisper quiet (not much louder than the JC10) but a beast to move around. It had a honda gas motor at one time and I ended up with a motor from a compressor out of a Hechs that was remodeled. I believe it was a 20-30 gallon tank and used for the Sprinkler system to keep it pressurized or something like that. Anyway I use the Senco for anything, besides roofing and heavy framing so I do not have to move the Emglo.

The specs seem pretty close to each other JC10 40lbs Senco 38lbs, JC10 seems quieter  [smile] So I think the JC10 should be compared to the Senco PC0968 and not the 1010

http://www.cposenco.com/senco-pc0968-1-5-hp-2-5-gallon-oil-less-hand-carry-air-compressor/sennpc0968,default,pd.html?start=1&cgid=senco-compressors

That's what I had said (post #10).   [smile]

Oh sorry…Great minds think alike lol. Well I agree with you haha.

 

[Tim Sproul]

Tim, what application do you want the higher pressure for?

Just want the increased reservoir without increased heft.

 

[bonedaddy]

The Rol-air JC10 is very quiet and has great recovery.  It’s a fantastic unit.  If you want something smaller I would recommend the Bostitch  CAP-1512.  Just as light as the Senco 1010 but with much quicker recovery.  I used it all the time for a small, mobile, light weight compressor.  It will even run a framer if needed.

http://www.amazon.com/Bostitch-Gallon-High-Output-Compressor-CAP1512/dp/B004285RLS

 

[upscale]

something smaller I would recommend the Bostitch  CAP-1512.  Just as light as the Senco 1010 but with much quicker recovery.  I used it all the time for a small, mobile, light weight compressor.  It will even run a framer if needed.

Any idea how many decibels the CAP-1512 is when recycling? Sent a query to Stanley, but haven't heard back yet.

 

[Ken Nagrod]

something smaller I would recommend the Bostitch  CAP-1512.  Just as light as the Senco 1010 but with much quicker recovery.  I used it all the time for a small, mobile, light weight compressor.  It will even run a framer if needed.

Any idea how many decibels the CAP-1512 is when recycling? Sent a query to Stanley, but haven't heard back yet.

Your probably not going to be able to compare that way.  The specs on dB vary acording to things like distance from the source while testing, where it was tested, the operator and equipment testing it, the scale that was used for testing.  I've looked at dB specs from many manufacturers and they're all over the place and unreliable, I feel.  Best to test at least two models you're interested in, right in front of you or at least get that kind of feedback from others who have.

 

[upscale]

Best to test at least two models you're interested in, right in front of you or at least get that kind of feedback from others who have.

You're absolutely correct of course, I'm just having mucho trouble finding a local dealer Toronto that has a Senco JC1010 in stock. Atlas has the Rol-air JC10 in stock and they're perfectly willing to let me have a listen, but they don't have the JC1010. The Rol-air is approximately twice the weight of the JC1010. For a reasonably light and small compressor with a 'reputed' lower noise level, the JC1010 is my guestimate for a baseline.

Unfortunately, here in the great white north, we are deprived of tool dealers stocking every tool on the market and can't compare them in person as easily as one might find in our neighbours to the south.   :  (No insult to our Canadian dealers who actually do quite well in meeting market demand)

 

[bonedaddy]

When I had both the Senco and Bostitch they seemed close to each other in volume of noise with the Senco being maybe a slight bit quieter.  I think Bostitch rates the CAP-1512 at 80db.  The Rol-Air is much quieter than either one (72db), but almost 2x the weight.  Both the Senco and Bostitch are very easy to transport.  The Rol-Air isn’t too bad but I much prefer to carry the Bostitch up any stairs.  (22lbs)

 

[hemdale]

Hi guys,

Does anyone know about the PC1010N ?
Just wondered if anyone tried this one. Is it an upgrade fromthe classic 1010 version ?

Cheers