OF 1400 vs OF 2200

[Jalvis]

You probably are sold on the LR32 but if I were willing to drill one hole at a time then there are better options.  

I'm sold on the LR32 not just because of the shelf pins but also boring hinge cups and the easy of use on multiple doors and shelves.  After watching Brice Burrell's video at the Festool Training class using the parallel guides and the LR32 system, I was sold.  I could mass produce shelf pins and bore hinge cups without constantly setting up the configuration/registration.   

I understand the method you trying to accomplish.  Since thats the case the 2200 is not an option.

My only concern with the system you describe is with long panels.....5-7 feet.  Probably best for anything that fits on one MFT.  Although I would like to see the application for the longer sides.

 

[CarolinaNomad]

My only concern with the system you describe is with long panels.....5-7 feet.  Probably best for anything that fits on one MFT.  Although I would like to see the application for the longer sides.
[/quote]

I think it's possible.  May need to use a full sheet on top of the MFT under the long panels in order to have something to clamp too.  But I'm only guessing, considering I haven't won the lottery yet. [big grin]

Anybody want to donate to a good cause?  My wife keeps calling me crazy for drinking the green kool-aid.

 

[Stone Message]

....
There is an easy workaround for this that enables you to use 3 1/2" panel-raising bits in an OF1400 in a CMS. I mentioned it in another thread some time ago. Clamp a 1/4" piece of plywood or MDF to the CMS with a hole cut out in the middle to accommodate the bit. It is a little tricky to insert the bit into the OF1400 from above the CMS table but it can be done.

Now with the bit at the correct final height, start your routing. Note that you have to move the fence incrementally instead of raising the bit as you would normally do. But the end result is the same and you still take small cuts.

I should add that this is a totally safe procedure and the bit is still fully seated in the collet.

Richard is right - this is the way that I have to do it with my cheap and cheerful homemade tables. I am sure that the OF1400 has the guts to do the work.

Peter

 

[CarolinaNomad]

There is an easy workaround for this that enables you to use 3 1/2" panel-raising bits in an OF1400 in a CMS. I mentioned it in another thread some time ago. Clamp a 1/4" piece of plywood or MDF to the CMS with a hole cut out in the middle to accommodate the bit. It is a little tricky to insert the bit into the OF1400 from above the CMS table but it can be done.

Now with the bit at the correct final height, start your routing. Note that you have to move the fence incrementally instead of raising the bit as you would normally do. But the end result is the same and you still take small cuts.

I should add that this is a totally safe procedure and the bit is still fully seated in the collet.
[/quote]

Just so I'm clearing, you are speaking of a Horizontal 3 1/2" Panel-Raising Bit?  And your taking small cuts horizontally instead of vertically.

 

[mouppe]

There is an easy workaround for this that enables you to use 3 1/2" panel-raising bits in an OF1400 in a CMS. I mentioned it in another thread some time ago. Clamp a 1/4" piece of plywood or MDF to the CMS with a hole cut out in the middle to accommodate the bit. It is a little tricky to insert the bit into the OF1400 from above the CMS table but it can be done.

Now with the bit at the correct final height, start your routing. Note that you have to move the fence incrementally instead of raising the bit as you would normally do. But the end result is the same and you still take small cuts.

I should add that this is a totally safe procedure and the bit is still fully seated in the collet.

Just so I'm clearing, you are speaking of a Horizontal 3 1/2" Panel-Raising Bit?  And your taking small cuts horizontally instead of vertically.
[/quote]

Yes, and yes!

You still have some vertical adjustment on the bit as well, but the whole bit has to sit clear of the CMS plate as it is too large for the aperture.

http://www.amazon.com/Freud-99-571-2-Inch-Raised-Backcutters/dp/B00075M6LO

 

[CarolinaNomad]

Thanks!  They need an emoticon with a light blinking over its head.  Due to budget reasons and still need to get the job done, I've decided to keep my 2.25 hp Bosch router and dedicate it to a Crestonwood router table.  And get the 1400 for all free hand work plus the LR 32.