air compressor in systainer
- Thread starter WAKA2020
- Start date
WAKA2020,
In this category, (quiet, oil-free, moderate pressure, etc.) all the compressors I have seen appear to be based on the wob-l pump design. https://www.usathomas.com/WOB-L-PISTON_c_11.html
These compressors do work well for intermittent use. Running these systems near rated pressure for anything more than a short span will have an adverse affect on service life. Keep in mind that this type of compressor is not designed for a long service life to start with.
Based on the similarities between compressors in this category, you may want to base your decision more on the type of work you are doing. If one of these units suits your needs, just choose the one that has the most appealing features, color, price, etc.
Once you have selected a unit, you shouldn't have too much trouble sourcing a suitable low-cost replacement pump if trouble arises.
Good Luck!
In this category, (quiet, oil-free, moderate pressure, etc.) all the compressors I have seen appear to be based on the wob-l pump design. https://www.usathomas.com/WOB-L-PISTON_c_11.html
These compressors do work well for intermittent use. Running these systems near rated pressure for anything more than a short span will have an adverse affect on service life. Keep in mind that this type of compressor is not designed for a long service life to start with.
Based on the similarities between compressors in this category, you may want to base your decision more on the type of work you are doing. If one of these units suits your needs, just choose the one that has the most appealing features, color, price, etc.
Once you have selected a unit, you shouldn't have too much trouble sourcing a suitable low-cost replacement pump if trouble arises.
Good Luck!
Peter Kelly
Member
- Joined
- Aug 22, 2012
- Messages
- 363
I have a 18 gage and a 15 gage Milwaukee nailer. I like both of them. However note on the 15 gage, which is rated to shoot 2½" nails, that there is not much tolerance on the high side. I bought some from Lowes and they would not feed. I forget which brand though.
This is more of a complaint about the nails than the nailer.
The driving factor was doing trim in a small bathroom. With the compressor in the room maneuvering was difficult with the air hose. And the Porter Cable gun was acting up again so I made the plunge to battery power. I did not weigh it, but it feels lighter than the PC.
It makes sense to pick one manufacturer and stay in the system. Milwaukee was easily available and competitive. I don't know if it is better or as good as the other brands.
This is more of a complaint about the nails than the nailer.
The driving factor was doing trim in a small bathroom. With the compressor in the room maneuvering was difficult with the air hose. And the Porter Cable gun was acting up again so I made the plunge to battery power. I did not weigh it, but it feels lighter than the PC.
It makes sense to pick one manufacturer and stay in the system. Milwaukee was easily available and competitive. I don't know if it is better or as good as the other brands.
Cheese
Member
- Joined
- Jan 16, 2015
- Messages
- 12,501
Here are a bunch of threads about compressors in Systainers.
https://www.festoolownersgroup.com/...-airstak-rolair-jc10-mod/msg541494/#msg541494
https://www.festoolownersgroup.com/ask-festool/festoolcadex-compressor/msg611148/#msg611148
https://www.festoolownersgroup.com/...systainer-compressors-available-for-pre-order!-(us)/msg573928/#msg573928
And here's a nice shot that Dick came up with, a Rolair JC 10 on the bottom and a Systainer lid on the top to start off the stack. [cool]
[attachimg=1]
https://www.festoolownersgroup.com/...-airstak-rolair-jc10-mod/msg541494/#msg541494
https://www.festoolownersgroup.com/ask-festool/festoolcadex-compressor/msg611148/#msg611148
https://www.festoolownersgroup.com/...systainer-compressors-available-for-pre-order!-(us)/msg573928/#msg573928
And here's a nice shot that Dick came up with, a Rolair JC 10 on the bottom and a Systainer lid on the top to start off the stack. [cool]
[attachimg=1]
Attachments
Do you mean to leave it in the Systainer while running, or just use the Systainer for storage?
You will note that all the compressors seem to have cooling fins. Running the compressor in a closed space would, I imagine, reduce the life expectancy of the compressor.
You will note that all the compressors seem to have cooling fins. Running the compressor in a closed space would, I imagine, reduce the life expectancy of the compressor.
usernumber1
Member
- Joined
- Aug 7, 2018
- Messages
- 406
I like my cadex its ready to go in 5 seconds i don't see that mentioned on other compressors much. They need 55sec pump up time for the rolair jc10
It's not whisper quiet but not terrible either. I like the sys4 footprint. Up down stairs, stacking in the car. rolling out of the elevator with the sys stack, I just don't want to carry a separate roll cage
that home made dolly solution looks pretty cool but need to make it and that takes time
use it for nailing and stapling, it's more than sufficient. I would get whatever is easier to service in your area
EDIT: oh, if you want to compare some techs, compare the rated duty cycle, that will tell you a lot more and you can match to your needs
It's not whisper quiet but not terrible either. I like the sys4 footprint. Up down stairs, stacking in the car. rolling out of the elevator with the sys stack, I just don't want to carry a separate roll cage
that home made dolly solution looks pretty cool but need to make it and that takes time
use it for nailing and stapling, it's more than sufficient. I would get whatever is easier to service in your area
EDIT: oh, if you want to compare some techs, compare the rated duty cycle, that will tell you a lot more and you can match to your needs
Is there a version of this available in the US?
https://www.senco-emea.com/product/22881/ac4504-low-noise-compressor
I have one in a T-Loc IV and it's a very neat fit. Space for a coiled 3/8" line etc.
Very quiet too at 58db (Lpa) and at less than €200 including 24% sales tax up here, a good value option.
It's somewhat similar to the PC1010 but a good bit quieter and doesn't need any messing to fit it in a T-Loc.
I use it reasonably often with a range of Senco tools, 18g finish nailer, 23g pin nailer and an 18g crown stapler and upholstery stapler.
https://www.senco-emea.com/product/22881/ac4504-low-noise-compressor
I have one in a T-Loc IV and it's a very neat fit. Space for a coiled 3/8" line etc.
Very quiet too at 58db (Lpa) and at less than €200 including 24% sales tax up here, a good value option.
It's somewhat similar to the PC1010 but a good bit quieter and doesn't need any messing to fit it in a T-Loc.
I use it reasonably often with a range of Senco tools, 18g finish nailer, 23g pin nailer and an 18g crown stapler and upholstery stapler.
jamiljonna
Member
- Joined
- Apr 25, 2015
- Messages
- 19
So is the Cadex no longer available?
