CMS OF with the 2200 and Tongue and Groove cutter 491034 - Table build

[Phil Beckley]

Hi
  I am making a table for the reception here at Festool U.K and decided to just use what is available which is 60x20mm Ash. Using the CMS OF with the 2200 and the Tongue and groove cutter (lightning cutter  [big grin]) to joint the tops together.....will post some updates through next week.
rg
Phil

 

[Shane Holland]

Gotta love being able to toss the UG extension on there for an outfeed. So nice when everything works together.

Thanks for sharing, Phil.

 

[Phil Beckley]

Gotta love being able to toss the UG extension on there for an outfeed. So nice when everything works together.

Thanks for sharing, Phil.

.....cool way to work  [smile]

 

[Phil Beckley]

....in total I ran 88m of jointing with only a small amount of chips lost and one bag change. All in the clamps to dry off over the weekend......CMS OF with the 2200 is one of my personal favourites [thumbs up]
The top will have one of the SYS AZ drawers hung from the underside....just to give it the Festool look, a bit of green does no harm  [wink]
rg
Phil

 

[Phil Beckley]

.....and sanded with the RO 150 and cut to width with the CS 70

 

[Phil Beckley]

.....and then cut on the MFT 3 to length and mitred with the TSC  [smile]

 

[Phil Beckley]

.....cool cut straight from TSC with 28t blade

 

[Phil Beckley]

....and then Domino DF 500 to joint the mitre....

 

[Shane Holland]

[thumbs up]

 

[tjbnwi]

Been doing the same since I got my first TS.

Nice when the grain cooperates.

Tom

 

[Lbob131]

Is the 491034  not a glue joint cutter?

 

[Phil Beckley]

Been doing the same since I got my first TS.

Nice when the grain cooperates.

Tom

........just given me an idea - maybe a design change  [thumbs up]
rg
Phil

 

[Phil Beckley]

Is the 491034  not a glue joint cutter?

.....yup, heard that before.
rg
Phil

 

[Lbob131]

Does a decent job either way.

 

[sancho57]

Gotta love being able to toss the UG extension on there for an outfeed. So nice when everything works together.

Thanks for sharing, Phil.

.....cool way to work  [smile]

Ya could of come over and we could of built that in my shop bud. What ya don't like Mrs Jobbys burgers ??? [big grin] [big grin] [big grin]

 

[tjbnwi]

Been doing the same since I got my first TS.

Nice when the grain cooperates.

Tom

........just given me an idea - maybe a design change  [thumbs up]
rg
Phil

Full view.

Tom

 

[Phil Beckley]

Been doing the same since I got my first TS.

Nice when the grain cooperates.

Tom

........just given me an idea - maybe a design change  [thumbs up]
rg
Phil

Full view.

Tom

Cool design Tom  [smile] I used most of the off cuts from the timber I use on the Dealer courses so wrapping the grain around was preferred but not possible. Having seen your design I like the idea of running the TS down the joint lines and setting in a line.....
rg
Phil

 

[tjbnwi]

Tom

 

[Phil Beckley]

Gotta love being able to toss the UG extension on there for an outfeed. So nice when everything works together.

Thanks for sharing, Phil.

.....cool way to work  [smile]

Ya could of come over and we could of built that in my shop bud. What ya don't like Mrs Jobbys burgers ??? [big grin] [big grin] [big grin]

.....bring them over here.....and the BBQ!! [wink]
RG
Phil

 

[tjbnwi]

Gotta love being able to toss the UG extension on there for an outfeed. So nice when everything works together.

Thanks for sharing, Phil.

.....cool way to work  [smile]

Ya could of come over and we could of built that in my shop bud. What ya don't like Mrs Jobbys burgers ??? [big grin] [big grin] [big grin]

.....bring them over here.....and the BBQ!! [wink]
RG
Phil

Sounds like Phill is opening Festool UK for jobsworths BBQ bash. [big grin]

Tom