New TXS Compact Drill, Centrotec Installers Set, & SysLite II - Coming Dec. 1st!

[Shane Holland]

Just to clarify are the drills are going to be offered all the time correct. The only limited time is the installers set.

The only limited time items are the Centrotec Set and the ZOBO bits.

The TXS and SysLite are regular catalog items.

 

[Gwerner]

So is the only difference between the TXS and CXS the shape?

 

[Shane Holland]

So is the only difference between the TXS and CXS the shape?

Yup! That's it. [member=43644]Gwerner[/member]

 

[Potts17]

I just ordered the Centrotec set as well. You can never have too many bits!

 

[Shane Holland]

Figured I'd add a little eye candy to entice you Centrotec Set fence sitters...  [poke]

[attachimg=1]

[attachimg=2]

Contents:

Centrotec Components

(1) 492135 Centrotec Chuck
(1) 200140 Centrotec Handle Driver
(1) 466108 Centrotec Countersink Bit
(1) 492540 BV150 Centrotec Bit Extension
(1) 498974 BH60 Centrotec Bit Holder
(1) 492648 BHS65 Centrotec Bit Holder
(1) 492520 Centrotec D2-8mm Pilotless Countersink
(1) 495133 Centotec Socket Adapter 3/8"
(1) 495131 Centotec Socket Adapter 1/4"
(1) 496936 TwinBox Bit Set (bit storage with one each: PH1, PH2, PH3, PZ1, PZ2, T15, T20, T25, T30, Slotted)
(1) 496450 Keyless Centrotec Chuck Adapter FP
(1) Systainer T-LOC SYS 1

4" (100mm) Centrotec Driver Bits

(1) Square Drive #1
(1) Square Drive #2
(1) Square Drive #3
(1) Phillips #1
(1) Phillips #2
(1) Phillips #3
(1) Torx T15
(1) Torx T20
(1) Torx T25
(1) Torx T30

1" (25mm) Wire Detent Driver Bits

(5) Square Drive #1
(10) Square Drive #2
(5) Square Drive #3
(5) Phillips #1
(10) Phillips #2
(5) Phillips #3
(5) Torx T15
(5) Torx T20
(5) Torx T25
(5) Torx T30

Brad Point Centrotec Drill Bits

(1) 1/8" Centrotec Brad Point Wood Bit
(1) 3/16" Centrotec Brad Point Wood Bit
(1) 1/4" Centrotec Brad Point Wood Bit
(1) 5/16" Centrotec Brad Point Wood Bit
(1) 3/8" Centrotec Brad Point Wood Bit
(1) 7/16" Centrotec Brad Point Wood Bit
(1) 1/2" Centrotec Brad Point Wood Bit

You may notice, as I did, that there are some incorrect bits shown in the photos. Not to worry, I verified with Festool USA that it was just a photo issue and the correct bits would be in the kit.

 

[jimbo51]

Drill, bits and light are about $729.00. That will make a very nice start on paying for my new HKC next spring.

Of course I may have to deduct some for a combo Systainer sometime.

 

[#Tee]

yes!! now this is an announcement! kalII and the installer set is finally back!

 

[jacko9]

Is there an Installer set with metric drill bits?

Jack

 

[tjbnwi]

Brent sent me the shank diameters on the square drive.

#1=4mm
#2=5mm
#3=6mm

Kreg pocket holes are 3/8" (9mm), so we're good.  [thumbs up]

The shank diameter may enter the bore, but I believe the 4" is not long enough to prevent the chuck/Centrotec holder from rubbing the work piece. I'll check over the next few days. Of course you can use an bit holder, but you don't need the Centrotec cut to make that work.

Tom

 

[Shane Holland]

Is there an Installer set with metric drill bits?

[member=8318]jacko9[/member], only one version this time, all imperial.

The shank diameter may enter the bore, but I believe the 4" is not long enough to prevent the chuck/Centrotec holder from rubbing the work piece. I'll check over the next few days. Of course you can use an bit holder, but you don't need the Centrotec cut to make that work.

[member=4105]tjbnwi[/member], Tom I thought about that. The standard Kreg bit is 6" if I remember correctly. Didn't go check mine. But I figured with the Centrotec chuck being smaller in diameter than a keyless chuck and the fact that less bit was in the chuck, it wouldn't be a problem. But your confirmation would be appreciated. Or, I can test in the next day or so myself down in the shop. I think my Kreg jig is still packed up from my last move since I use mostly Dominos. So I need to hunt down my jig. [wink]

 

[tjbnwi]

Is there an Installer set with metric drill bits?

[member=8318]jacko9[/member], only one version this time, all imperial.

The shank diameter may enter the bore, but I believe the 4" is not long enough to prevent the chuck/Centrotec holder from rubbing the work piece. I'll check over the next few days. Of course you can use an bit holder, but you don't need the Centrotec cut to make that work.

[member=4105]tjbnwi[/member], Tom I thought about that. The standard Kreg bit is 6" if I remember correctly. Didn't go check mine. But I figured with the Centrotec chuck being smaller in diameter than a keyless chuck and the fact that less bit was in the chuck, it wouldn't be a problem. But your confirmation would be appreciated. Or, I can test in the next day or so myself down in the shop. I think my Kreg jig is still packed up from my last move since I use mostly Dominos. So I need to hunt down my jig. [wink]

I have the 4" #2 Robertson Atlas Machine bit , I'll check once I drill a pocket hole.  I do believe (from recollection) the Centrotec does rub the material.

Tom

 

[Firestorm]

Can I assume that these products will also be available through Canadian Dealers as well? Can I pre-order through Lee Valley or KMS or some other dealer?

Thanks

Bryan

Edmonton, Alberta, Canada

 

[TylerC]

Can I assume that these products will also be available through Canadian Dealers as well? Can I pre-order through Lee Valley or KMS or some other dealer?

Thanks

Bryan

Edmonton, Alberta, Canada

Yes, these will be available in both the US and Canada on Dec. 1.

Also for our Canadian friends, the CT MINI and MIDI will be available again on Dec. 1.

 

[Sean7a]

Hallelujah, midi's n mini's are back for Canada.  See our friend [member=7294]Shawn[/member] at Atlas in Toronto for that hook up.

 

[Shane Holland]

This Centrotec Set is no different than the ones from years past... the interest level is very high. With limited quantities available, I would suggest anyone interested order one sooner rather than wait.

And, like Sean said, glad that our friends up north are getting the smaller vacs back.  [thumbs up]

 

[Rob in Vancouver]

Any idea what the selling price will be for the installers set in CAD $?

 

[Shane Holland]

Any idea what the selling price will be for the installers set in CAD $?

[member=57769]TylerC[/member] can give you Canadian pricing.

 

[#Tee]

shane is there a installer kit with zobo bits avail in NA?

 

[Shane Holland]

shane is there a installer kit with zobo bits avail in NA?

No. There's only a single version of the Centrotec Set this time around.

The ZOBOs are available separately.

 

[TylerC]

Any idea what the selling price will be for the installers set in CAD $?

Here's the Canadian suggested pricing for the new items: 

Centrotec Installer Set $395.00
TXS Basic $310.00
TXS Set $376.00
SysLite II $257.00
SysLite II Set $330.00
CT MINI Dust Extractor $627.00
CT MIDI Dust Extractor $693.00