Recon Tool is starting today (Cont. US Only)

[promark747]

For those who just bought the OF2000, here's a tip I found to keep the dust shroud secure (the vac hose can easily yank it out if you're not careful and the plastic tabs that snap in can be a bit fragile).  Order a couple of extra knobs off of EKAT and then use a wire or piece of rubber strapping to hold the shroud in place.  I got the idea from one of AskWoodman's YouTube videos.  What I would like to do eventually is figure out a way to make an extension to the shroud (or a new one altogether) using a 3D printer.  Something that would go higher up toward the motor.

 

[wow]

For those who just bought the OF2000, here's a tip I found to keep the dust shroud secure (the vac hose can easily yank it out if you're not careful and the plastic tabs that snap in can be a bit fragile).  Order a couple of extra knobs off of EKAT and then use a wire or piece of rubber strapping to hold the shroud in place.  I got the idea from one of AskWoodman's YouTube videos.  What I would like to do eventually is figure out a way to make an extension to the shroud (or a new one altogether) using a 3D printer.  Something that would go higher up toward the motor.

That's a great idea! Let me know if you make one, please?

 

[TheWarrior]

Lets see a picture of that Planex! I think I want one, just don't know if I will use it enough to justify it

I'll take that pic next week when I can put it to use! Its an impressive machine. Will definitely help beef up your shoulders as its got some mass. I can see what they did for helping to keep weight down, but when you figure the strength it needs to handle the operator pressing it into a wall or ceiling, I feel the weight is decent and the construction is stout. Might get the support harness for big jobs!

 

[Wenyce]

For those who just bought the OF2000, here's a tip I found to keep the dust shroud secure (the vac hose can easily yank it out if you're not careful and the plastic tabs that snap in can be a bit fragile).  Order a couple of extra knobs off of EKAT and then use a wire or piece of rubber strapping to hold the shroud in place.  I got the idea from one of AskWoodman's YouTube videos.  What I would like to do eventually is figure out a way to make an extension to the shroud (or a new one altogether) using a 3D printer.  Something that would go higher up toward the motor.

Thank you I will def give that a go and amazingly I was thinking of doing the same thing once I get my personal fabricator.

 

[NHSP759]

For those who just bought the OF2000, here's a tip I found to keep the dust shroud secure (the vac hose can easily yank it out if you're not careful and the plastic tabs that snap in can be a bit fragile).  Order a couple of extra knobs off of EKAT and then use a wire or piece of rubber strapping to hold the shroud in place.  I got the idea from one of AskWoodman's YouTube videos.  What I would like to do eventually is figure out a way to make an extension to the shroud (or a new one altogether) using a 3D printer.  Something that would go higher up toward the motor.

Thanks Promark! I'll give it a shot in a week when I get back from Florida. The router starts sooooooo smooth!!

 

[Walk On Wood]

Ordered Monday thru Bob, received package Thursday.

Packing was adequate, all 3 systainers looked brand new. The RAS had a few SLIGHT scuffs on it, the ETS125 and RO125 both looked brand new. I wouldn't have known they weren't new stock except for the refurbished stickers on the outside of the systainers.  All 3 sanders were purchased at the 20% off price, and to be honest, are in better condition than I expected. I use my tools heavily, so things like scuffs/scratches/dust don't faze me at all, I will be putting those marks on them all in short order. My primary concern is functionality, so I am very happy overall. 

 

[wow]

I measured the OF 2000 router. When it's sitting flat on the table (and assuming that it's not in a plunged position) the overall height is 12.5 inches. So it definitely will not stand upright in a Sys4.

Does anyone know if the OF 2200 router lays down or stands up in it's systainer?

 

[epicxt]

The of2200 t-loc insert has the router laying on a diagonal in order to fit into the sys4.

 

[copcarcollector]

Does anyone know if the OF 2200 router lays down or stands up in it's systainer?

 

[wow]

I just looked at the insert and there is a part number: 465797.  Hope that helps.

  called Festool just now and they couldn't find that part number. They gave me part number 467745, for $16 and change. Price shipped was under $25 so I ordered one.

I'll post whatever mods are required to fit it into a T-LOC once I get it

 

[Sparktrician]

WOO-HOO!!!  The Brown Box just dumped a Carvex on my doorstep!!! 

[big grin]

 

[Brandon]

Got my 30% off REQ today and I was very happy with the condition. Nearly new, just a little bit of dust, no scratches and the systainer and blade are perfect. I didn't even open the guide rail but I believe it's brand new.

 

[wow]

I just looked at the insert and there is a part number: 465797.  Hope that helps.

  called Festool just now and they couldn't find that part number. They gave me part number 467745, for $16 and change. Price shipped was under $25 so I ordered one.

I'll post whatever mods are required to fit it into a T-LOC once I get it.

Got my insert today. Positioned it in the T-LOC Sys 4 and the problem became obvious. At the bottom of the front edge inside the Sys 4 there is a small plastic rib for rigidity. Hopefully you can see it in this picture:

[attachimg #]

The picture is taken from above the Sys 4 looking down at the bottom, with the front facing you.

The problem with the insert is also obvious:

[attachimg #]

There is no spot for that rib to fit. My solution was to chuck a 3/16" drill bit into the good 'ole M12 Milwaukee, then position it at a 45 degree angle where the insert goes from horizontal to vertical. Doing so will provide enough space for the insert to clear the rib at the bottom as well as at the front, and the circle will provide stress relief for the notch. But now that the hole is there, the question becomes how to cut down each side and connect neatly up to the circle? There must be a tool for that, isn't there?

Wait, I know:

[attachimg #]

I *knew* that First Aid Kit would have other good uses!

[big grin]

And here is what my mod looks like when it's finished:

[attachimg #]

I put it in the Sys 4 and it fit perfectly the first time. This has to be my slickest and quickest mod ever!

 

[Walk On Wood]

Just received my 20% off Kapex

Festool box
Kapex box in the box
Kapex... A few very minor scuffs, a little dust.  The blade has clearly been used. I will do a test cut in the next couple of days and post more feedback then.  So far so good, thanks Bob!

 

[grbmds]

I got a 20% off ETS15/5 that was essentially new. I found no marks and no evidence of use. I feel I got a great deal. Tried it out and it works great. I do have some questions which I will address in another post.

 

[DrD]

Never bought a reconditioned tool.  I'm maybe interested in getting a ts55r.  Do the recon'd saws come with rails?  And if so, can you substitute rails, and for what incremental cost?  Thanks for your help.

DrD

 

[duburban]

Never bought a reconditioned tool.  I'm maybe interested in getting a ts55r.  Do the recon'd saws come with rails?  And if so, can you substitute rails, and for what incremental cost?  Thanks for your help.

DrD

I think thats a no, its been discussed. That would be best served by a new saw with your preferred dealer.

 

[semenza]

Never bought a reconditioned tool.  I'm maybe interested in getting a ts55r.  Do the recon'd saws come with rails?  And if so, can you substitute rails, and for what incremental cost?  Thanks for your help.

DrD

I think thats a no, its been discussed. That would be best served by a new saw with your preferred dealer.

  They come with rails but swapping the rail lengths/ type would be up to individual dealers. And is probably not possible for the reconditioned saws.

Seth

 

[DrD]

Thanks for the response!  Think I'll pass on a recon'd saw; with only a 1yr warranty and maybe restrictions on guide rails, there's not enough savings even at 20% off to make it attractive.

 

[Administrator_JSVN]

More tools added to the list. Get 'em while they're available!

http://www.festoolusa.com/power-tools/reconditioned/

Including SysLites (at the bottom of the list)!