What Festool Did You buy Today?

[Holz-Her]

 

[griffs]

A bit early but a new sander in November when Axminster tools open their new branch in Cardiff.

 

[Kev]

Freehand diamond cutting system, an FS angle guide and a 90th Anniversary blue Systainer.

 

[nobbyharding]

Rotex 90 and 300 pads for delta and 90mm - so if I had bought one of the cheap type of sanders with far inferior dust collection 0 the pad costs offset the cost of the Rotex to about £90

Some of 8mm router bits of 1400 dust collector for side fence

 

[Kev]

Vecturo set and HL850

 

[Holmz]

Freehand diamond cutting system, an FS angle guide and a 90th Anniversary blue Systainer.

[member=13058]Kev[/member]
Does it work as good as it looks like it does in the videos?

 

[Kev]

Freehand diamond cutting system, an FS angle guide and a 90th Anniversary blue Systainer.

[member=13058]Kev[/member]
Does it work as good as it looks like it does in the videos?

[member=40772]Holmz[/member]
I haven't tried it yet, but if it's anything like it's rail based companions it should be excellent (the basis on which I got it).

 

[mdc]

Already a few weeks ago i bought the PD 20/4 and some long Centrotec bits. Earlier than planned but the price was too good 

 

[Gavin1987]

Cxs and 1400 guide rail

 

[Ohc917]

Heavy duty centrotec.

 

[tjbnwi]

Glue pucks for the Conturo and the 1.5 mm round over bit.

I told someone I did not have any white pucks for my Conturo, so he picked up the pucks and the bit. I can pay for them tomorrow when he comes over to use the Conturo  ???[eek]. Things that make you go hummmmmmm.  [unsure]

Tom

 

[rst]

I just recieved the RAS 115 and 24 - 80 grit papers from Toolnut.

 

[Mbconstructionjoinery]

Picked up a 3m guide rail today  [big grin]

 

[Darren1972]

Carvex 18 li jigsaw

 

[VW mick]

C18 basic and an empty sys2 For my new fien

 

[Zebt]

My first machine from Festool! The RO125 FEQ Plus. I feel like i've fallen off a cliff and it's a long long way to the bottom [scared].... I have been in and out of the shop so many times for 3 years, yes, 3 years and I have finally broken. I think they were very relieved at Northern Abrasives here in Brookvale that I finally opened my wallet. [laughing] I did get a free tape measure though.. [big grin]

 

[bertv]

When I was hunting for a piece of wood yesterday, I could not resist picking up a SECOND CSX… It is my favorite tool and now I have TWO!

 

[Darren1972]

C18 basic and an empty sys2 For my new fien

Fein can come in a sys my multimaster did

 

[Kev]

More blades for TS75 and KAPEX ... plus ordered some Metabo cordless gear that should land in Oz within 2 weeks.

(and asked them to please hurry up my HKC55 set) [sad]

 

[Bitbob]

My first machine from Festool! The RO125 FEQ Plus. I feel like i've fallen off a cliff and it's a long long way to the bottom [scared].... I have been in and out of the shop so many times for 3 years, yes, 3 years and I have finally broken. I think they were very relieved at Northern Abrasives here in Brookvale that I finally opened my wallet. [laughing] I did get a free tape measure though.. [big grin]

Our local dealer gives nothing away for free and the fsz120's I purchased today were 2 euros more than Festool's recommended retail price.