Cordless trim routers - DeWalt vs Bosch

[derekcohen]

Yesterday, as my wife and I wandered through lines of power tools at the store where I was collecting sanding disks, she reminded me that I have a birthday coming up and should get something I would enjoy using. She is a keeper.

I really have all the power tools I need but would like to upgrade the corded Makita trim router. That it is corded is not the issue - but having one less cord to connect up would be pleasant. I discovered this recently with a small cordless Makita angle grinder and a Festool ROS. I use power tools in short bursts, with preference going to non-power hand tools.

One of the issues in the above paragraph is acquiring another battery system. I have tried hard to avoid to avoid this, and stuck with Festool drills, and recently a Festool ETSC-2 ROS. But Festool do not offer a trim router, cordless or otherwise.

There are four features i seek in a trim router:

1. A light, balanced machine capable of being used comfortbly in one hand.

2. Ease of height adjustment. This is the bane of my life with regards the Makita trim router. Too coarse for my liking, too much hunt-and-seek. A dedicated fine adjuster is preferred.

3. A plunge base to convert from fixed format. Prior to the Makita some 5 years ago, my experience was only with plunge routers, and I have come to value this feature when starting and ending a cut, where needed.

4. It would be ideal if trim routers came with a 1/2" shank facility, but that will never happen (as it would create a potentially dangerous machine), but 8mm shanks are pretty good for smoothing vibration and strength, and preferred to 1/4". There are an increasing number of 8mm options coming to the market - I think that manufacturers are recognising this factor. Anyway, I have both sizes, but would prefer a trim router with a 8mm collet as well as 1/4". My Makita has this.

My research tells me that the DeWalt and Bosch trim routers are the ones to beat. The DeWalt appears to have the better height adjustment, but the Bosch is more compact and slimmer in the hand. They have similar power, but I am not fussed by the amount of power, oer se. Can one get small batteries for these routers to reduce weight up high? I use only 3.0 in my Festool drills, preferring to have two and keep the extra charged. I am sure I have seen both 1/4" and 8mm collets available for the DeWalt, but it gets sold with one or the other, not both (depends on the country). Is there an 8mm available for the Bosch? What are the respective plunge bases like for each of these routers?

Your input - experience even if only having used one or the other - is valued.

Best wishes for the festive season.

Regards from Perth

Derek

 

[Cheese]

The MFKC 700 KA EB has been recently released in the UK, Germany & the Netherlands, you may want to keep your eyes open for that. I'd assume it'll be available in Australia sooner than in the States.
That would certainly tick most if not all of the boxes.

 

[Michael Kellough]

This new Festool looks like it’s meant just for trimming edge banding, having minimal (but very precise) depth adjustment.

 

[Cheese]

Well here's the new MFKC 700 EB. It appears to fit in all of the available bases.

 

[derekcohen]

Unfortunately, the Trimmer Router MFKC 700 is an edge router only. that, it can only work close to the edge of a board.

Regards from Perth

Derek

 

[tsmi243]

Unfortunately, the Trimmer Router MFKC 700 is an edge router only. that, it can only work close to the edge of a board.

Regards from Perth

Derek

?

It's certainly optimized for edges, but what makes you say it can't be used like any other router?

 

[Michael Kellough]

 

[Michael Kellough]

The above pic shows both routers parked at their lowest position each with a 2amp battery.

Girth Dewalt max 29cm, mid 28cm, min 27.5cm

Girth Bosch max 27.3cm, min 23.3cm. The min girth is higher up, possibly above comfortable range, if a longer bit is being used for a surface cut or shallow rabbet.

Both have fine depth adjustment but if you prefer to “read” the relative bit depth rather than measure, and expect to change bits frequently, then the Dewalt has the advantage. The Bosch adjustment wheel is the small red disk near the base. It turns a 1mm pitch screw. It has four hash marks so you can “read” 1/4mm increments directly but the marks are far enough apart that you can further subdivide the wheel for finer adjustment.

One important note is that my US purchased Dewalt did not include any kind of dust collection chute. The Bosch included two or three.

 

[Crazyraceguy]

Derek, you are absolutely right about the depth adjustment on the fixed-base Makita. The corded and cordless are physically identical otherwise, so the alternate bases all interchange. The plunge base is very nice, easily adjustable, and solid. I had one of the corded models, for quite some time, before the cordless became available. For the work I needed them to do, cordless was way better. That was already my battery platform, so it was greatly appreciated.
I use them for edge treatment/flush-trimming most of the time, leaving them as "set ups." Most of them are not critical, depth-wise, so it doesn't matter. When it does matter, leaving it "set up" makes the adjustment hassle way less important. I know I'm an anomaly, but it works for me.
If it's more than a simple trim, I go to OF1010, one of those is set up with a bushing and 1/4" up spiral bit. The other is "free", though I usually leave whatever bit was there last. That can save time too, maybe not every time, but often enough.
As far as alternatives; I have used quite a few of them. I don't like that extra diameter of the DeWalt, it is just too wide. The depth adjuster is indeed better, but holding it is more important to me.
If I didn't already have a platform commitment, or didn't mind adding another, Milwaukee would get my vote.
The fit to the hands is good, the depth adjustment is more like the Bosch, and they have additional bases.

 

[smorgasbord]

3. A plunge base to convert from fixed format. Prior to the Makita some 5 years ago, my experience was only with plunge routers, and I have come to value this feature when starting and ending a cut, where needed.

Do you not already have the plunge base for the Makita?

I agree with you that the Makita fixed base height adjustment is crude, but the plunge base is just dandy - and everything fits both the corded and cordless. Plus, Makita is a very good battery system to get into. I can never keep track of which 18v DeWalt battery is which - Milwaukee isn't much better.

You might want to also consider getting precision collets for whatever router you run. These tend to grip better and are dynamically balanced. Here's a source:

https://elairecorp.com/routercollets/

For the Makita, a cheaper source ($25 for both) for ⅛" and ¼" precision collets is:

Precision Collets for Carbide Compact Router

If you need replacement collets for your Carbide Compact Router, these are for you. What's included: .25" Precision Collet .125" Precision Collet These are made in the US for Carbide 3D. NOTE: These collets are included with the Carbide Compact Router. These are available separately only for...

shop.carbide3d.com

 

[WillAdams]

Note that Elaire Corp. also sells precision collets for the Makita RT0701/0700 (and by extension, the matching 0702 and battery units):

Makita Style Router Collets - Elaire Corp

Standard Collet for Makita Routers; RT700C, RT0700CX3, RT0701C, RP0900K, 3621, 3621A

elairecorp.com

and note that that they have 8mm (and other sizes).