Domino mounted to LR32 plate

Number one son Ryan is on a bicycle approximately half way between Washington, D.C. and Pittsburgh (camping along the way).  When he gets back later this week I'll pass a nudge on to him for this project.  My work is 99% done, it's now up to him to market them (as well as several other projects in the hopper -- NUDGE, NUDGE).  [unsure]
 
Go, Ryan, Go!  Sounds like a fun trip.

Seneca Woodworking has a lot in the pipeline - the plate mount for the domino, parallel guides, the XL Domiplate and new bits, anything else?  I'm looking forward to the new products!

    Scott

 
sheeschen said:
Go, Ryan, Go!  Sounds like a fun trip.

Seneca Woodworking has a lot in the pipeline - the plate mount for the domino, parallel guides, the XL Domiplate and new bits, anything else?  I'm looking forward to the new products!

     Scott
Click to expand...

The "Fency-Shims" for the XL Domino to handle thinner stock and a couple of others that are escaping me at the moment. 
http://festoolownersgroup.com/festool-tools-accessories/which-domino-to-buy/

The Lad needs to play a bit less & work a bit more...  [unsure]
 
Hi Ron,

I'd like to nudge you again on your mounting plate.  I was looking at Jerry Works' solution and it looks like his way the front bolt interferes with the angle lock down lever on the domino, making it less secure than I'd like.  If others have tried it, I'd be interested in their experience.

Any date yet for your release?

Thanks,

Dick
 
Wouldn't it be easier to just mount the domino over the existing LR 32 hole? All you'd need is a few threaded holes machined into the domino fence.

Or make a part that slips over like the cross stop, and that attaches to the plate....
 
Been there. Done that. Look up Tomiplate if you art curious. My setup does not require modifications to the LR32 plate either! So far I gave only used it in the lateral fashion i.e. the domino in the horizontal plane.
 
I am new enough to the site that I had never seen this. Seems like a neat idea from Ron, but is there any kind of update or is it a dead product?
 
RonWen said:
[attachthumb=#]

[attachthumb=#]

[attachthumb=#]

[attachthumb=#]
Click to expand...

Ron,

Did you take this any further, or has this been abandoned? I take it you didn't get a lot of interest, or was there something that didn't work?

Thanks
 
Since it's close to Halloween, I figured it was OK to raise this thread from the dead and since this all took place before I was a member, why did this not happen?

I have the newer DF500 with the tabs not the pins, and I don't believe Jerry Works' solution to mount the DF500 on the LR32 guide plate will work for me (no pun intended).

Went to Seneca's website but couldn't find anything about this.
 
I can't recall it all now, but it had issues with just doing that.  I have tab model Dominos myself.
 
Won't work with the tab Domino, as the idea is to register and align the domino on the LR 32 plate just using the pins.
 
Gregor said:
Won't work with the tab Domino, as the idea is to register and align the domino on the LR 32 plate just using the pins.
Click to expand...

Yes, that's what I was saying, won't work with newer Domino machines.
 
Nothing to be sorry for Gregor, I was just agreeing with you.
 
To risk asking a stupid question....Why do you want to mount the Domino to the LR32 rail?
 
You must log in or register to reply here.

Similar threads

P
Domino on 13 mm plate
Replies
2
Views
952
ChuckM
C
S
Domino Face Mortising Jig - Any Interest?
2
Replies
38
Views
4K
smorgasbord
S
M
Blum hinge 79B3598 mounting plate selection confusion
Replies
4
Views
7K
Crazyraceguy
Crazyraceguy
R
SOLD Festool 494340 LR32 Guide Plate AND 5mm 491066 Router Bit
Replies
2
Views
253
regdor1999
R
P
A good idea with improvements, but mistakes were made along the way.
Replies
6
Views
281K
Packard
P
Back
Top