Miter Saw recommendation?

[pettyconstruction]

I think you will like and keep the saw.

My reasons for getting the Kapex are :
1. Weight , for a 10” saw it’s manageable
2. Compact size , can use against the wall and it stores well.
3: accurate cuts
4: dust control, weather inside or out , the lack of dust is very pleasant . Short 36mm hose.
Btw, I went with a non anti static Festool hose , I read that the saw is ground. Seems to work just fine.
Enjoy,
Charlie

Sent from my iPad using Tapatalk Pro

 

[rjboch]

After unboxing, I used the new Kapex throughout the weekend in support of my current projects (e.g., remodel of a bath, laundry room, and building new laundry cabinets). I have one word to describe – AWESOME! This is seriously in a different league than any previous miter saw experience…and in a great way. I am now looking for new excuses to use it  

I am so happy that I decided to go for it. It’s basically driving a Ford your whole life and then getting a BMW (basically same analogy could be used to describe most Festool experiences). Life changer and more reason to continue with my Festool addiction. I have a 36mm hose on order, as recommended, and should kick the dust collection up a notch from my 27mm hose.

Lastly, I recognize and I am grateful that I was able to make this purchase and so happy to add this machine to my shop.

 

[threesixright]

Good for you. I had same dilemma, but can say very happy with my KAPEX!

Sent from my iPhone using Tapatalk

 

[ChuckM]

Convincing. Just ordered one.

The million $ stick can also be used on the table saw with the cross-cut sled or panel sled.

 

[rmhinden]

Based on the discussion here, I got a million $ stick for my Kapex.

One thing I noticed, is that when use the stick to apply pressure to hold the board, the wood moves a little (away from the stick).

Suggestions on how to avoid this?

 

[ChuckM]

Apply downward pressure, not forward or sideway pressure. When you start, apply light to medium pressure to ensure the stock doesn't move, and then firm up the (downward) pressure a little bit. Over-pressuring could move the piece. If the stock is very thick, you can place a spacer block on the other end of the stick.

Practice it by holding down on a scrap on a surface without any fence and with a fence. Try it with both the single finger and double fingers.

 

[rmhinden]

Apply downward pressure, not forward or sideway pressure. When you start, apply light to medium pressure to ensure the stock doesn't move, and then firm up the (downward) pressure a little bit. Over-pressuring could move the piece. If the stock is very thick, you can place a spacer block on the other end of the stick.

Practice it by holding down on a scrap on a surface without any fence and with a fence. Try it with both the single finger and double fingers.

That helps, thanks!  It requires the right touch.

Bob

 

[semenza]

Based on the discussion here, I got a million $ stick for my Kapex.

One thing I noticed, is that when use the stick to apply pressure to hold the board, the wood moves a little (away from the stick).

Suggestions on how to avoid this?

    I notice that too. Need to be a little careful when pressing down. I found that it has to do with the stick flexing a bit when force is applied.  It is easy to check / watch if it moved if the saw has a laser. I think that it probably holds well with less pressure than seems necessary.  The tendency is to push hard on things that are made to hold things in place. I found that if I back off a little the piece doesn't move. Not trying to pin down a wild animal  [big grin]

Seth

 

[Bugsysiegals]

How do you know which size hose you got ... I've the CT 36 but not sure where on the hose you measure?

 

[semenza]

How do you know which size hose you got ... I've the CT 36 but not sure where on the hose you measure?

Measure the ID of the hose.  The Dxx are the ID in mm.  D27 = 27mm ID. 

If your CT36 is new and has the new style hose it is actually the new tapered hose. 32mm ID at the vac end and 27mm ID at the tool end. The tapered hose is currently supplied with all the vacs except the auto clean ( AC ), CT15,  and the CT-SYS.

Seth

 

[Mario Turcot]

[member=60777]Bugsysiegals[/member]

How do you know which size hose you got ... I've the CT 36 but not sure where on the hose you measure?

The CT 36 comes with smooth suction hose dia. 27/32 x 3.5 m AS/CT. 32mm at vaccum and 27mm at tools end.

Ref.https://www.festoolcanada.com/produ...ctors/574935---ct-36-e-hepa-usa-120v#Overview

 

[Bugsysiegals]

Thanks guys!

Sent from my iPhone using Tapatalk

 

[Jakez]

I'm going to add onto this thread - there are several on miter saws, but this one seems to be the most recent.

For awhile I had an old Craftsman compound miter saw. I decided to upgrade and eventually chose the Milwaukee 10in. It cuts fantastic and the weight is great. But the dust collection is awful. The Craftsman did pretty well, I also have a 7 1/4" Dewalt miter saw which has what I would say is very good dust collection.

That said, I'm looking for recommendations on miter saws with good dust collection. I'm considering the Kapex again - all the other Festool I have does great with dust collection - but the price is out there. Really I think I'd love the KS60 if only they brought that to the US. The other thing is not too heavy - my garage is my shop so everything gets moved in and out of place, and then put back away so I can get my car in.

How is the Dewalt DS780?

Thanks

 

[ben_r_]

I'm going to add onto this thread - there are several on miter saws, but this one seems to be the most recent.

For awhile I had an old Craftsman compound miter saw. I decided to upgrade and eventually chose the Milwaukee 10in. It cuts fantastic and the weight is great. But the dust collection is awful. The Craftsman did pretty well, I also have a 7 1/4" Dewalt miter saw which has what I would say is very good dust collection.

That said, I'm looking for recommendations on miter saws with good dust collection. I'm considering the Kapex again - all the other Festool I have does great with dust collection - but the price is out there. Really I think I'd love the KS60 if only they brought that to the US. The other thing is not too heavy - my garage is my shop so everything gets moved in and out of place, and then put back away so I can get my car in.

How is the Dewalt DS780?

Thanks

I had the DWS780 for a bit before moving to the Bocsh Glide 12" and while I liked the DeWalt, I really didnt like how much space was required behind the saw for clearance. That lead me to the Glide and I havent felt I needed anything more since.