What Festool Did You buy Today?

[ijhursh]

I scored a Sys-mft-fx today!!

Sent from my iPhone using Tapatalk

Old stock? Used? Auction? I see some going for $400(+), lol.

It was in a store, got it for the regular price, old stock!!

Sent from my iPad using Tapatalk

 

[ColossusX]

Just bought a SYS-MFT on Ebay.  Saved 15% with the app.  Can't wait to try it out

 

[sancho57]

You'll like it. If youd like , have a look at Peter Parfits video on Systainer storage. He has some good ideas for using the Sys MFT

 

[justaguy]

I bought a used Kapex.

I had used a Kapex at a friends shop and found a lot to like about the saw. I had been holding back on buying a new one based on the reported motor issues. I ran across a used unit in what appears to be good working condition and at the price I could not say no.

I'll check out the alignment tonight and mount a new blade. Fingers crossed..

 

[niky1]

DOMINO connector range KV-SYS D8 [eek] .....

 

[niky1]

Pin Festool (204147) ..... uff

 

[sancho57]

[member=37787]niky1[/member]

I got a pica pencil looks just like that wo the festool logo.

Pica Pencils are pretty nice.

Comes real handy especially the colored lead.

I use the red and yellow as much as the reg lead.

I got a couple of the festool ones coming.

After seeing you post and the picture , I ordered some of them well just because they got "festool" written on them which means they write much better  [big grin]

 

[sancho57]

After seeing and searching for the festool pica pencils I ordered a couple and seen this knife and got a couple coming to.

I already have the swiss army knife, but this is a cool looking knife. It has festool on it to so its got to be sharper then all the other knives  [big grin]

 

[ear3]

Bluetooth finally came back in stock at my local dealer!  CT module + controller and a 5.2Ah BT compatible battery.

 

[sancho57]

Got a couple of interface pads for my RO 150 and ES 150, and another one for my RS 400

 

[ceddy]

Finally got a 2nd MFT, can't believe I waited so long. Got a C15 off ebay for 225$, it's like new with batteries. Also got a new 27mm hose in the new style and new TS55 since I'm sick of having to swap out the TS75 from the CMS module.

 

[dltflt]

I just received my Braided 36mm x 3.5m hose. Also picked up a c18 5.2ah on the recon sale. The drill feels like a beast after using the CXS. Looking forward to trying it out.

 

[ear3]

5m braided 36mm hose.

I took advantage of the 50% discount on the sleeved hoses that started the other week, so I couldn't justify upgrading my 27mm hose to the braided version.  But I could on the 36mm -- which I typically use only with tools that have integral plugs, like the 2200 and the HL850, so there is no concern about having to buy yet another hose sleeve to couple a plug.  Plus 5m of length vs. my current 3.5 36mm hose.

So I will be joining those people who are flooding the second hand market with the older AS hoses when I put my current one up for sale after the new one arrives.

 

[dltflt]

I used my old 36mm x 3.5m hose to make a short hose for the Kapex and a short hose for my Contractor Saw Stop.

 

[Twoodman66]

Conturo with mft table, MFK700 , EB base ,1,1.5,2 & 3mm router bits. Sys vac 1 plus 2(x2)
And not festool but Lamello Zeta p2/diamond

 

[dltflt]

I just picked up an HL-850 for $250. It has two cutter heads. Looks to be in pretty good condition except for a small crack in the housing. I don’t think it will effect the performance.

 

[leakyroof]

Over the past couple of Months.... MX1200 mixer and blades, 3 new Flexible Hoses, one of which promptly took residence in my Workshop Cleaning Kit as a replacement for the old 36mm AS hose that the Kit comes with.
2 Bluetooth Batteries, one Bluetooth Remote Kit
Granat Mesh Abrasives for Drywall Sanding along with the intermediate/interface  pads for them
Used TS75 Saw... need to get a rail or two for it, but that can wait... [smile]
Had to pass on a nice used MK700 Router Kit, A/C work on my house killed the budget for that... [crying]
Oh and thanks to @sixpoint socket... ‘Oliver’... I bought that 5mm drill bit and depth set for shelf work....

 

[HowardH]

I just got the CMS jig saw insert for my Trion.  It's no bandsaw replacement but it really simplifies being able to cut curves without having to clamp and re-clamp constantly in order to not run into my MFT.  I'm just going to leave the Trion attached to it as I don't see needing to remove it unless for a special circumstance. It's a bit of a pain to unhook the hose and power cord every time I need to switch and install the router insert but for all of us that are space challenged, it's a pretty good solution.  I was amazed about how quickly it was sent from GB to Texas.  Only took 3 days to get here!

 

[sancho57]

[member=396]HowardH[/member]

I have one of those. They are great at making templates. Buy a variety of blades and they will  really help you scroll alot easier.

Im really surprised that Festool doesnt sell that in NA

 

[jugwaxer]

I purchased an ETS 150/5 from Woodcraft on clearance the other day. It is last year's model without the new pad. I have a DF500 and a TS55 and this may be my favorite Festool so far. And the clearance price put it at about the same cost as a Bosch 6" sander.