Festool 36mm(straight) braided hose

[Coen]

I see

 

[Rick Herrick]

But that is pieces/sections.  I was looking for a 1-piece wand.  Maybe I misunderstood.  I don't need it break down and fit into a systainer.  I should check the local vacuum store, maybe I could get lucky there.

 

[Coen]

Huh no. 447599 is one piece. According to the catalog... 1100mm long.

 

[FestitaMakool]

Cheese and Coen to the rescue..

Yes, it’s expensive, local to USD is $172.
It is made of aluminium, anodised.

 

[Rick Herrick]

I guess this picture is misleading a bit.  It does say 1100mm but that picture doesn't really look like that.

 

[Coen]

I guess this picture is misleading a bit.  It does say 1100mm but that picture doesn't really look like that.

Yeah that pic seems to be #440412

 

[FestitaMakool]

[attachimg=1]

Those are in plastic and are 970mm combined.

 

[Coen]

Yeah, and there is no plastic curved part in D50 to go with those.

For household use I have a 3-part telescopic Miele tube. Really nice. 1157 fully extended, just the telescopic tube. 568mm at the shortest. Compared to the 2-part one... at full length 13 cm longer... at shortest 4 cm shorter.

But they don't longer sell it... so hoping it will last...

When they bring in the news that 'long people get higher pay'.... that is all lost on things like longer vacuum cleaner tubes, longer mattress, bigger bicycle...

 

[Cheese]

Festool 447599https://www.festoolusa.com/accessory/447599---d-50-vr-m#Overview

[attachimg=1]

 

[FestitaMakool]

Yeah, and there is no plastic curved part in D50 to go with those.

When they bring in the news that 'long people get higher pay'.... that is all lost on things like longer vacuum cleaner tubes, longer mattress, bigger bicycle...

Exactly, and it’s why I too want one of those longer telescopic wands.. Once experienced that there is actually long enough wands that allows me to stand upright there’s an instant relief  [smile]

I too forgot to mention not seeing a curved 50mm part, not even in the 50mm hose and attachments set. I find it oddly, as I purchased a CT 26 lightly used a while back, with a lot of accessories in the hose and attachment department - and in this systainer where all the loose  parts were I found a curved 50mm plastic piece. There’s no stamp or print on it, but it fits perfect to Festool’s 50mm inside and outside (depending on which way you use it) I am pretty sure it’s a Festool item, but later I have never found one.

 

[Coen]

Maybe dig through ekat?

I can't remeber a curved 50mm part and I've a pretty good knowledge of the Festool catalog since about 2003

Although I recently put most of the paper catalogs in de paper bin  [sad]

 

[guybo]

Hi, bought this in 2009,all accessories for 27,36 and 50 listed.guy[attachimg=1]

 

[FestitaMakool]

Guys, I was wrong - I did find a part no’ - It’s a Bosch part:
[attachimg=1]

Beware: It is the narrow end that fits inside the vac side of the hose - as I do only have a couple of 50mm hoses, I haven’t had the opportunity to try it on the wands. That said, there’s a chance it won’t fit the wand (without heating or sanding)
It has the same appearance as Festool’s and Nilfisk..

 

[semenza]

This  CRAFTSMAN CMXZVBE38639 (or clone) bent tube fits the D50 hose end.  On my D50 hose it is a bit loose, but a couple wraps of electrical tape around the D50 connector (to fatin' it up) should do the trick. Mine is plenty tight with one wrap. Not AS. It does have a suction reducer.

Pull the tape tight. Keep it back from the end so that it doesn't catch. Trim off any wrinkled ends.

    [attachimg=1]              [attachimg=2]            [attachimg=3]

Seth

 

[rst]

I use Rocklers bent attachment with a handle and old CraCraftsman tubes with my Fein and Festool 58mm hoses

 

[jarbroen]

Does anyone have a part number for the Workshop kit referenced in post # 23? I looked all around on Festool US and didn't find it. I did find the metal vac head though.

Didn’t see your question earlier.  The part number I ordered for that kit is 576838.