TS55, OF1400 and OF1010 Imperial Depth Scale.

[Stokely]

I would buy one for my TS75, OF1400 and OF1010 in a heartbeat. Not sure id the current TS55 would match my saw. Is that possible?

I am working on 1010 now and TS75 is next. Are you setup where you could print a template for me and test? Just need a standard PC printer.

Rich

I wish. Getting the floors redone in my shop today and tomorrow, so I don't have access. Next week I will.

 

[rrmccabe]

That looks like WORK !

I think I have it covered now. Will report back with findings.

Rich

 

[rrmccabe]

Want to give a HUGE thank you to Steve at QWAS for helping me shake down the OF1010 router imperial labels today.

I am making a trip to the Woodsmith Store tomorrow with a final version of the decal to verify fit from the final printed copy and will have it available for purchase tomorrow.

I will check out the TS75 and OF2200 while I am there.

Appreciate everyone's interest. My mailbox has been quite busy with orders in the last 24 hours.  Glad I can contribute something to such a great product.

Rich

 

[Paul G]

Just to be slightly heartless....why?.....because I can.  [big grin] [big grin] [tongue] [tongue]

[attachimg=#]

I just applied that to my TS55 REQ and while I'm very glad something in inches was included, the lack of increment labels other than 0, 1 & 2 leaves a lot to be desired and plenty of room for improvement IMO.

 

[CCRT]

Just Ordered    Thanks

 

[rdaily]

Looking forward to the of1010 scale!

 

[copcarcollector]

Ordered! Thanks for offering these in yellow, I think it will be easier for me to see!! 

 

[Alan m]

any chance of a metric version.
i would like  one that allows for the rail

 

[rrmccabe]

Yes can do metric. Let me get AutoCAD work done.

Also the 1010 router labels will be online tonight for purchase. Thanks again to Steve at QWAS for doing a ton of the leg work!

 

[dicktill]

Already bought the TS-55 and OF 1400 stickers (great). Will also get an OF 1010 sticker when available. Can you also make the clear conversion stickers that you have on your guide rail(s) as shown in your Fleabay listings available? A package deal of say 5 or 6 would be nice.

Thanks, Dick

 

[Stokely]

Any ETA on TS75 and OF1010?

 

[rrmccabe]

Any ETA on TS75 and OF1010?

OF1010 will be available in about 2 hours. They are printed and ready to go.  I just need to put them on the payment page.

TS75 is going to be a challenge and don't expect anything for a week. the arc shaped label requires more work.

 

[Stokely]

Any ETA on TS75 and OF1010?

OF1010 will be available in about 2 hours. They are printed and ready to go.  I just need to put them on the payment page.

TS75 is going to be a challenge and don't expect anything for a week. the arc shaped label requires more work.

No problem! No hurry on this end. I still have no floor. Just inquiring. I will wait to buy all of them when you are ready. Thanks for your work on this!!

 

[rrmccabe]

Great !  I have a call to make tomorrow to see if I can get a TS75.

Here is a picture of the OF1010 on Steve (QWAS) router. They are available now.

 

[jtwood]

I'll be ordering for the OF1400 and the rail labels, and will definitely want a TS75 label when they are available.

Keep up the good work.

Steve

 

[rrmccabe]

any chance of a metric version.
i would like  one that allows for the rail

Alan, have a prototype. See attached.

Just trying to figure out the postage issues and cost going across the pond.

Rich

 

[Alan m]

thanks mr raccoon
i presum the squares are for the different comon materials  plus a little for the blade to project down

 

[rrmccabe]

The squares are currently imperial and probably wont make it to final design.  Since you are used to metric is there anything we can add?

I am going to add boxes around the numbers so they are bold and easy to read.

 

[Peter Durand]

Great !  I have a call to make tomorrow to see if I can get a TS75.

Here is a picture of the OF1010 on Steve (QWAS) router. They are available now.

I got mine a few days ago. That was nice quick service, thanks.

BTW, what is the model of your Deere mower with the front end shovel?

Cheers,

 

[rrmccabe]

Excellent.

It's a 2305 Compact Utility Tractor. Next step up from a garden tractor.  Have the loader (as you can see) and mower and snow blower.  We have 3 acres and 250' driveway. So gets a good workout year round.